Thermal conductivity against densityHigher and further left: spreads more heat for its weightThermal expansion against thermal conductivityLower and further right: warps less when heated
Try it on a partA bracket to run stress or thermal on, free in your browser
MIL-HDBK-5J, Metallic Materials and Elements for Aerospace Vehicle Structures (2003)U.S. Department of DefenseSteel AISI 4340 · Young's modulus (stiffness): MIL-HDBK-5J design value (AISI 4340, quenched and tempered)Steel AISI 4340 · Poisson's ratio: MIL-HDBK-5J design value (AISI 4340, quenched and tempered)
4
Typical Engineering Properties of PolypropyleneINEOS Olefins & Polymers USAarchived copyPlastic Polypropylene · Poisson's ratio: base material: polypropylene homopolymer family (INEOS Olefins & Polymers USA, Typical Engineering Properties of Polypropylene)Plastic Polypropylene · Thermal conductivity: base material: polypropylene homopolymer family (INEOS Olefins & Polymers USA, Typical Engineering Properties of Polypropylene)Plastic Polypropylene · Thermal expansion: base material: polypropylene homopolymer family (INEOS Olefins & Polymers USA, Typical Engineering Properties of Polypropylene)
Each number points to the document that states it, with the exact basis. Values without a number are computed from the sourced ones. "Not sourced" means no citable source states it (or only a specification minimum); figures computed from it are left out too.
Questions
Mechanical
Is Plastic Polypropylene stronger than Steel AISI 4340?
Steel AISI 4340 is stronger: its yield strength is 1,035 MPa against 33 MPa for Plastic Polypropylene (31.4x).
Which is lighter, Plastic Polypropylene or Steel AISI 4340?
Plastic Polypropylene is lighter: 900 kg/m³ against 7,840 kg/m³ for Steel AISI 4340.
Which is stiffer, Plastic Polypropylene or Steel AISI 4340?
Steel AISI 4340 is stiffer: Young's modulus 200 GPa against 1.45 GPa for Plastic Polypropylene, so the same part in Steel AISI 4340 deflects less under the same load.
Which is lighter for the same job, Plastic Polypropylene or Steel AISI 4340?
For the same stiffness or strength: Plastic Polypropylene is lighter for a stiff panel or plate, strong panel or plate; Steel AISI 4340 is lighter for a stiff rod or tie (tension), stiff beam (bending), strong rod or tie, strong beam.
Part that must be
Plastic Polypropylene
Steel AISI 4340
Stiff rod or tie (tension)
15.8x heavier
lighter
Stiff beam (bending)
35% heavier
lighter
Stiff panel or plate
lighter
1.69x heavier
Strong rod or tie
3.6x heavier
lighter
Strong beam
14% heavier
lighter
Strong panel or plate
lighter
1.56x heavier
For the same stiffness or strength, mass scales with density over stiffness (or strength) raised to a power set by how the part is loaded: 1 for a rod in tension, 1/2 for a beam in bending, 1/3 for a panel (the standard material-selection indices).
Thermal
Which conducts heat better, Plastic Polypropylene or Steel AISI 4340?
Steel AISI 4340 conducts heat better: 37.5 W/m·K against 0.195 W/m·K for Plastic Polypropylene.
Which expands less with temperature?
Steel AISI 4340 expands less: 11.3 µm/m·K against 90 µm/m·K for Plastic Polypropylene.