Thermal conductivity against densityHigher and further left: spreads more heat for its weightThermal expansion against thermal conductivityLower and further right: warps less when heated
Try it on a partA bracket to run stress or thermal on, free in your browser
Moplen HP501H Product DataLyondellBasellPlastic Polypropylene · Yield strength: typical, tensile stress at yield ISO 527Plastic Polypropylene · Young's modulus (stiffness): typical, tensile modulus ISO 527Plastic Polypropylene · Density: typical, 23 °C ISO 1183-1Plastic Polypropylene · Max service temperature: HDT 0.45 MPa (ISO 75B), unannealed
2
TIMETAL 6-4 PropertiesTIMETarchived copyTitanium · Yield strength: typical, plate (>0.187 in), annealed, 0.2% offsetTitanium · Ultimate tensile strength: typical, plate, annealedTitanium · Elongation at break: typical, in 2 in., plate annealedTitanium · Density: nominalTitanium · Poisson's ratio: mean of TIMET measurementsTitanium · Melting point: melting rangeTitanium · Max service temperature: upper recommended use temperature
3
TIMETAL 6-4 Data SheetTIMETarchived copyTitanium · Young's modulus (stiffness): typical range, 20 °CTitanium · Thermal conductivity: typical, 20 °C, mill annealedTitanium · Thermal expansion: typical, mean 0-100 °CTitanium · Specific heat: typical, 20 °C
4
Typical Engineering Properties of PolypropyleneINEOS Olefins & Polymers USAarchived copyPlastic Polypropylene · Poisson's ratio: base material: polypropylene homopolymer family (INEOS Olefins & Polymers USA, Typical Engineering Properties of Polypropylene)Plastic Polypropylene · Thermal conductivity: base material: polypropylene homopolymer family (INEOS Olefins & Polymers USA, Typical Engineering Properties of Polypropylene)Plastic Polypropylene · Thermal expansion: base material: polypropylene homopolymer family (INEOS Olefins & Polymers USA, Typical Engineering Properties of Polypropylene)
Each number points to the document that states it, with the exact basis. Values without a number are computed from the sourced ones. "Not sourced" means no citable source states it (or only a specification minimum); figures computed from it are left out too.
Questions
Mechanical
Is Plastic Polypropylene stronger than Titanium?
Titanium is stronger: its yield strength is 885 MPa against 33 MPa for Plastic Polypropylene (26.8x).
Which is lighter, Plastic Polypropylene or Titanium?
Plastic Polypropylene is lighter: 900 kg/m³ against 4,430 kg/m³ for Titanium.
Which is stiffer, Plastic Polypropylene or Titanium?
Titanium is stiffer: Young's modulus 115 GPa against 1.45 GPa for Plastic Polypropylene, so the same part in Titanium deflects less under the same load.
Which is lighter for the same job, Plastic Polypropylene or Titanium?
For the same stiffness or strength: Plastic Polypropylene is lighter for a stiff panel or plate; Titanium is lighter for a stiff rod or tie (tension), stiff beam (bending), strong rod or tie, strong beam, strong panel or plate.
Part that must be
Plastic Polypropylene
Titanium
Stiff rod or tie (tension)
16x heavier
lighter
Stiff beam (bending)
1.81x heavier
lighter
Stiff panel or plate
lighter
15% heavier
Strong rod or tie
5.45x heavier
lighter
Strong beam
1.82x heavier
lighter
Strong panel or plate
5% heavier
lighter
For the same stiffness or strength, mass scales with density over stiffness (or strength) raised to a power set by how the part is loaded: 1 for a rod in tension, 1/2 for a beam in bending, 1/3 for a panel (the standard material-selection indices).
Thermal
Which conducts heat better, Plastic Polypropylene or Titanium?
Titanium conducts heat better: 6.6 W/m·K against 0.195 W/m·K for Plastic Polypropylene.
Which expands less with temperature?
Titanium expands less: 9 µm/m·K against 90 µm/m·K for Plastic Polypropylene.