Thermal conductivity against densityHigher and further left: spreads more heat for its weightThermal expansion against thermal conductivityLower and further right: warps less when heated
Try it on a partA bracket to run stress or thermal on, free in your browser
Sources5 documents: Outokumpu, Carpenter Technology, U.S. Department of Defense, Steel Construction Institute
Stainless Steel 303
1.4305 / UNS S30300, Outokumpu typical values (hot rolled, solution annealed) from 'Steel Grades, Properties and Global Standards'; max service from Carpenter CarTech 303 datasheet
MIL-HDBK-5J, Metallic Materials and Elements for Aerospace Vehicle Structures (2003)U.S. Department of DefenseSteel AISI 4340 · Young's modulus (stiffness): MIL-HDBK-5J design value (AISI 4340, quenched and tempered)Steel AISI 4340 · Poisson's ratio: MIL-HDBK-5J design value (AISI 4340, quenched and tempered)
4
Design Manual for Structural Stainless Steel, 4th Edition (P413)Steel Construction Institutearchived copyStainless Steel 303 · Poisson's ratio: design value (structural stainless steels)
5
Carpenter Stainless Type 303 Data SheetCarpenter Technologyarchived copyStainless Steel 303 · Max service temperature: continuous, scaling limit
Each number points to the document that states it, with the exact basis. Values without a number are computed from the sourced ones. "Not sourced" means no citable source states it (or only a specification minimum); figures computed from it are left out too.
Questions
Mechanical
Is Stainless Steel 303 stronger than Steel AISI 4340?
Steel AISI 4340 is stronger: its yield strength is 1,035 MPa against 275 MPa for Stainless Steel 303 (3.76x).
Which is lighter, Stainless Steel 303 or Steel AISI 4340?
Steel AISI 4340 is lighter: 7,840 kg/m³ against 7,900 kg/m³ for Stainless Steel 303.
Which is stiffer, Stainless Steel 303 or Steel AISI 4340?
Stainless Steel 303 is stiffer: Young's modulus 200 GPa against 200 GPa for Steel AISI 4340, so the same part in Stainless Steel 303 deflects less under the same load.
Which is lighter for the same job, Stainless Steel 303 or Steel AISI 4340?
For the same stiffness or strength: Steel AISI 4340 is lighter for a strong rod or tie, strong beam, strong panel or plate.
Part that must be
Stainless Steel 303
Steel AISI 4340
Stiff rod or tie (tension)
about equal
about equal
Stiff beam (bending)
about equal
about equal
Stiff panel or plate
about equal
about equal
Strong rod or tie
3.79x heavier
lighter
Strong beam
2.44x heavier
lighter
Strong panel or plate
1.95x heavier
lighter
For the same stiffness or strength, mass scales with density over stiffness (or strength) raised to a power set by how the part is loaded: 1 for a rod in tension, 1/2 for a beam in bending, 1/3 for a panel (the standard material-selection indices).
Which is more ductile, Stainless Steel 303 or Steel AISI 4340?
Stainless Steel 303 stretches further before it breaks: 35% elongation at break against 18% for Steel AISI 4340.
Thermal
Which conducts heat better, Stainless Steel 303 or Steel AISI 4340?
Steel AISI 4340 conducts heat better: 37.5 W/m·K against 15 W/m·K for Stainless Steel 303.
Which expands less with temperature?
Steel AISI 4340 expands less: 11.3 µm/m·K against 16 µm/m·K for Stainless Steel 303.