Thermal conductivity against densityHigher and further left: spreads more heat for its weightThermal expansion against thermal conductivityLower and further right: warps less when heated
Try it on a partA bracket to run stress or thermal on, free in your browser
Sources5 documents: Kaiser Aluminum, Outokumpu, U.S. Department of Defense, Steel Construction Institute, Carpenter Technology
Aluminum 5052-H32
5052-H32, Kaiser Aluminum tube & pipe typical datasheet (mechanical, CTE, melting); MIL-HDBK-5J (Poisson, density, specific heat)
Stainless Steel 303
1.4305 / UNS S30300, Outokumpu typical values (hot rolled, solution annealed) from 'Steel Grades, Properties and Global Standards'; max service from Carpenter CarTech 303 datasheet
1
Alloy 5052 Tube & Pipe Technical DataKaiser Aluminumarchived copyAluminum 5052-H32 · Yield strength: typical, 0.2% offsetAluminum 5052-H32 · Ultimate tensile strength: typicalAluminum 5052-H32 · Elongation at break: typicalAluminum 5052-H32 · Young's modulus (stiffness): typicalAluminum 5052-H32 · Thermal conductivity: base material: 5052 in O temper (same alloy, annealed); Kaiser typicalAluminum 5052-H32 · Thermal expansion: typical, mean 20-100 °CAluminum 5052-H32 · Melting point: melting range
2
Steel Grades, Properties and Global StandardsOutokumpuarchived copyStainless Steel 303 · Yield strength: Outokumpu typical (product P = hot rolled plate, transverse)Stainless Steel 303 · Ultimate tensile strength: Outokumpu typicalStainless Steel 303 · Elongation at break: Outokumpu typical, A5Stainless Steel 303 · Young's modulus (stiffness): at RT (Table 12)Stainless Steel 303 · Density: at RTStainless Steel 303 · Thermal conductivity: at RTStainless Steel 303 · Thermal expansion: mean, 20–100 °CStainless Steel 303 · Specific heat: at RT
3
MIL-HDBK-5J, Metallic Materials and Elements for Aerospace Vehicle Structures (2003)U.S. Department of DefenseAluminum 5052-H32 · Density: nominalAluminum 5052-H32 · Poisson's ratio: typical (handbook physical constant)Aluminum 5052-H32 · Specific heat: at 100 °C (212 °F); table covers O, H32, H34, H36, H38
4
Design Manual for Structural Stainless Steel, 4th Edition (P413)Steel Construction Institutearchived copyStainless Steel 303 · Poisson's ratio: design value (structural stainless steels)
5
Carpenter Stainless Type 303 Data SheetCarpenter Technologyarchived copyStainless Steel 303 · Max service temperature: continuous, scaling limit
Each number points to the document that states it, with the exact basis. Values without a number are computed from the sourced ones. "Not sourced" means no citable source states it (or only a specification minimum); figures computed from it are left out too.
Questions
Mechanical
Is Aluminum 5052-H32 stronger than Stainless Steel 303?
Stainless Steel 303 is stronger: its yield strength is 275 MPa against 195 MPa for Aluminum 5052-H32 (41%).
Which is lighter, Aluminum 5052-H32 or Stainless Steel 303?
Aluminum 5052-H32 is lighter: 2,685 kg/m³ against 7,900 kg/m³ for Stainless Steel 303.
Which is stiffer, Aluminum 5052-H32 or Stainless Steel 303?
Stainless Steel 303 is stiffer: Young's modulus 200 GPa against 70 GPa for Aluminum 5052-H32, so the same part in Stainless Steel 303 deflects less under the same load.
Which is lighter for the same job, Aluminum 5052-H32 or Stainless Steel 303?
For the same stiffness or strength: Aluminum 5052-H32 is lighter for a stiff rod or tie (tension), stiff beam (bending), stiff panel or plate, strong rod or tie, strong beam, strong panel or plate.
Part that must be
Aluminum 5052-H32
Stainless Steel 303
Stiff rod or tie (tension)
lighter
3% heavier
Stiff beam (bending)
lighter
1.74x heavier
Stiff panel or plate
lighter
2.07x heavier
Strong rod or tie
lighter
2.09x heavier
Strong beam
lighter
2.34x heavier
Strong panel or plate
lighter
2.48x heavier
For the same stiffness or strength, mass scales with density over stiffness (or strength) raised to a power set by how the part is loaded: 1 for a rod in tension, 1/2 for a beam in bending, 1/3 for a panel (the standard material-selection indices).
Which is more ductile, Aluminum 5052-H32 or Stainless Steel 303?
Stainless Steel 303 stretches further before it breaks: 35% elongation at break against 12% for Aluminum 5052-H32.
Thermal
Which conducts heat better, Aluminum 5052-H32 or Stainless Steel 303?
Aluminum 5052-H32 conducts heat better: 138 W/m·K against 15 W/m·K for Stainless Steel 303.
Which expands less with temperature?
Stainless Steel 303 expands less: 16 µm/m·K against 23.8 µm/m·K for Aluminum 5052-H32.