Thermal conductivity against densityHigher and further left: spreads more heat for its weightThermal expansion against thermal conductivityLower and further right: warps less when heated
Try it on a partA bracket to run stress or thermal on, free in your browser
Alloy 5052 Tube & Pipe Technical DataKaiser Aluminumarchived copyAluminum 5052-H32 · Yield strength: typical, 0.2% offsetAluminum 5052-H32 · Ultimate tensile strength: typicalAluminum 5052-H32 · Elongation at break: typicalAluminum 5052-H32 · Young's modulus (stiffness): typicalAluminum 5052-H32 · Thermal conductivity: base material: 5052 in O temper (same alloy, annealed); Kaiser typicalAluminum 5052-H32 · Thermal expansion: typical, mean 20-100 °CAluminum 5052-H32 · Melting point: melting range
2
TIMETAL 6-4 PropertiesTIMETarchived copyTitanium · Yield strength: typical, plate (>0.187 in), annealed, 0.2% offsetTitanium · Ultimate tensile strength: typical, plate, annealedTitanium · Elongation at break: typical, in 2 in., plate annealedTitanium · Density: nominalTitanium · Poisson's ratio: mean of TIMET measurementsTitanium · Melting point: melting rangeTitanium · Max service temperature: upper recommended use temperature
3
TIMETAL 6-4 Data SheetTIMETarchived copyTitanium · Young's modulus (stiffness): typical range, 20 °CTitanium · Thermal conductivity: typical, 20 °C, mill annealedTitanium · Thermal expansion: typical, mean 0-100 °CTitanium · Specific heat: typical, 20 °C
4
MIL-HDBK-5J, Metallic Materials and Elements for Aerospace Vehicle Structures (2003)U.S. Department of DefenseAluminum 5052-H32 · Density: nominalAluminum 5052-H32 · Poisson's ratio: typical (handbook physical constant)Aluminum 5052-H32 · Specific heat: at 100 °C (212 °F); table covers O, H32, H34, H36, H38
Each number points to the document that states it, with the exact basis. Values without a number are computed from the sourced ones. "Not sourced" means no citable source states it (or only a specification minimum); figures computed from it are left out too.
Questions
Mechanical
Is Aluminum 5052-H32 stronger than Titanium?
Titanium is stronger: its yield strength is 885 MPa against 195 MPa for Aluminum 5052-H32 (4.54x).
Which is lighter, Aluminum 5052-H32 or Titanium?
Aluminum 5052-H32 is lighter: 2,685 kg/m³ against 4,430 kg/m³ for Titanium.
Which is stiffer, Aluminum 5052-H32 or Titanium?
Titanium is stiffer: Young's modulus 115 GPa against 70 GPa for Aluminum 5052-H32, so the same part in Titanium deflects less under the same load.
Which is lighter for the same job, Aluminum 5052-H32 or Titanium?
For the same stiffness or strength: Aluminum 5052-H32 is lighter for a stiff beam (bending), stiff panel or plate; Titanium is lighter for a strong rod or tie, strong beam, strong panel or plate.
Part that must be
Aluminum 5052-H32
Titanium
Stiff rod or tie (tension)
about equal
about equal
Stiff beam (bending)
lighter
29% heavier
Stiff panel or plate
lighter
40% heavier
Strong rod or tie
2.75x heavier
lighter
Strong beam
1.66x heavier
lighter
Strong panel or plate
29% heavier
lighter
For the same stiffness or strength, mass scales with density over stiffness (or strength) raised to a power set by how the part is loaded: 1 for a rod in tension, 1/2 for a beam in bending, 1/3 for a panel (the standard material-selection indices).
Which is more ductile, Aluminum 5052-H32 or Titanium?
Titanium stretches further before it breaks: 16% elongation at break against 12% for Aluminum 5052-H32.
Thermal
Which conducts heat better, Aluminum 5052-H32 or Titanium?
Aluminum 5052-H32 conducts heat better: 138 W/m·K against 6.6 W/m·K for Titanium.
Which expands less with temperature?
Titanium expands less: 9 µm/m·K against 23.8 µm/m·K for Aluminum 5052-H32.