Thermal conductivity against densityHigher and further left: spreads more heat for its weightThermal expansion against thermal conductivityLower and further right: warps less when heated
Try it on a partA bracket to run stress or thermal on, free in your browser
MIL-HDBK-5J, Metallic Materials and Elements for Aerospace Vehicle Structures (2003)U.S. Department of DefenseSteel AISI 4340 · Young's modulus (stiffness): MIL-HDBK-5J design value (AISI 4340, quenched and tempered)Aluminum 7075-T6 · Poisson's ratio: typical (handbook physical constant)Steel AISI 4340 · Poisson's ratio: MIL-HDBK-5J design value (AISI 4340, quenched and tempered)
4
Alloy 7075 Sheet, Coil & Plate Technical DataKaiser Aluminumarchived copyAluminum 7075-T6 · Density: nominalAluminum 7075-T6 · Thermal conductivity: typical, 20 °C, T651Aluminum 7075-T6 · Thermal expansion: typical, mean 20-100 °CAluminum 7075-T6 · Specific heat: typical, at 100 °CAluminum 7075-T6 · Melting point: melting range
Each number points to the document that states it, with the exact basis. Values without a number are computed from the sourced ones. "Not sourced" means no citable source states it (or only a specification minimum); figures computed from it are left out too.
Questions
Mechanical
Is Aluminum 7075-T6 stronger than Steel AISI 4340?
Steel AISI 4340 is stronger: its yield strength is 1,035 MPa against 503 MPa for Aluminum 7075-T6 (2.06x).
Which is lighter, Aluminum 7075-T6 or Steel AISI 4340?
Aluminum 7075-T6 is lighter: 2,800 kg/m³ against 7,840 kg/m³ for Steel AISI 4340.
Which is stiffer, Aluminum 7075-T6 or Steel AISI 4340?
Steel AISI 4340 is stiffer: Young's modulus 200 GPa against 71 GPa for Aluminum 7075-T6, so the same part in Steel AISI 4340 deflects less under the same load.
Which is lighter for the same job, Aluminum 7075-T6 or Steel AISI 4340?
For the same stiffness or strength: Aluminum 7075-T6 is lighter for a stiff beam (bending), stiff panel or plate, strong rod or tie, strong beam, strong panel or plate.
Part that must be
Aluminum 7075-T6
Steel AISI 4340
Stiff rod or tie (tension)
about equal
about equal
Stiff beam (bending)
lighter
1.67x heavier
Stiff panel or plate
lighter
1.98x heavier
Strong rod or tie
lighter
36% heavier
Strong beam
lighter
1.73x heavier
Strong panel or plate
lighter
1.95x heavier
For the same stiffness or strength, mass scales with density over stiffness (or strength) raised to a power set by how the part is loaded: 1 for a rod in tension, 1/2 for a beam in bending, 1/3 for a panel (the standard material-selection indices).
Which is more ductile, Aluminum 7075-T6 or Steel AISI 4340?
Steel AISI 4340 stretches further before it breaks: 18% elongation at break against 11% for Aluminum 7075-T6.
Thermal
Which conducts heat better, Aluminum 7075-T6 or Steel AISI 4340?
Aluminum 7075-T6 conducts heat better: 130 W/m·K against 37.5 W/m·K for Steel AISI 4340.
Which expands less with temperature?
Steel AISI 4340 expands less: 11.3 µm/m·K against 23.4 µm/m·K for Aluminum 7075-T6.