Materials / Compare
Ceramic Alumina 96% vs. Plastic LCP GF30 Compare Ceramic Alumina 96% vs. Plastic LCP GF30 strength, stiffness, weight and thermal properties.
Change either side
Plastic PLA Plastic PETG Plastic ABS Plastic TPU Plastic Nylon Plastic ABS (bulk/injection) Plastic Polycarbonate Plastic POM/Acetal Plastic Nylon PA6 Plastic Nylon PA66 Plastic PEEK Plastic PTFE Plastic UHMWPE Plastic HDPE Plastic Polypropylene Plastic PMMA Plastic PBT GF30 Plastic PPS GF40 Plastic LCP GF30 Rubber Wood Aluminum Aluminum 6061-T6 Aluminum 7075-T6 Aluminum 2024-T351 Aluminum 5052-H32 Aluminum 7050-T7451 Aluminum A380 Aluminum 6063-T6 Aluminum 1100-O Aluminum ADC12 Steel Steel AISI 1018 Steel AISI 1045 Steel AISI 4340 Steel A992 Iron Titanium Titanium Ti-6Al-4V Stainless Steel 304 Stainless Steel 316 Stainless Steel 303 Stainless Steel 17-4PH Brass C360 Brass C260 Copper C110 Glass Nickel Inconel 718 Magnesium AZ31B-H24 Magnesium AZ91D Zinc Zamak 3 FDM ASA FDM Polycarbonate FDM PAHT-CF FDM HIPS SLA Resin Standard SLA Resin Tough 2000 SLA Resin Elastic 50A SLS PA12 Nylon DMLS AlSi10Mg Aluminum DMLS Ti-6Al-4V ELI Titanium DMLS 316L Stainless Steel DMLS 17-4PH Stainless Steel Concrete Brick Plywood Drywall PCB Laminate FR-4 Silicon Ceramic Alumina 96% Ceramic Aluminum Nitride Solder SAC305 Ceramic Alumina 96% Sintered ceramic (pressed and fired) Plastic PLA Plastic PETG Plastic ABS Plastic TPU Plastic Nylon Plastic ABS (bulk/injection) Plastic Polycarbonate Plastic POM/Acetal Plastic Nylon PA6 Plastic Nylon PA66 Plastic PEEK Plastic PTFE Plastic UHMWPE Plastic HDPE Plastic Polypropylene Plastic PMMA Plastic PBT GF30 Plastic PPS GF40 Plastic LCP GF30 Rubber Wood Aluminum Aluminum 6061-T6 Aluminum 7075-T6 Aluminum 2024-T351 Aluminum 5052-H32 Aluminum 7050-T7451 Aluminum A380 Aluminum 6063-T6 Aluminum 1100-O Aluminum ADC12 Steel Steel AISI 1018 Steel AISI 1045 Steel AISI 4340 Steel A992 Iron Titanium Titanium Ti-6Al-4V Stainless Steel 304 Stainless Steel 316 Stainless Steel 303 Stainless Steel 17-4PH Brass C360 Brass C260 Copper C110 Glass Nickel Inconel 718 Magnesium AZ31B-H24 Magnesium AZ91D Zinc Zamak 3 FDM ASA FDM Polycarbonate FDM PAHT-CF FDM HIPS SLA Resin Standard SLA Resin Tough 2000 SLA Resin Elastic 50A SLS PA12 Nylon DMLS AlSi10Mg Aluminum DMLS Ti-6Al-4V ELI Titanium DMLS 316L Stainless Steel DMLS 17-4PH Stainless Steel Concrete Brick Plywood Drywall PCB Laminate FR-4 Silicon Ceramic Alumina 96% Ceramic Aluminum Nitride Solder SAC305 Plastic LCP GF30 Bulk polymer (molded or machined) Try it on a partA sample part to run stress or thermal on, free in your browser Open in LessCAD Open in LessCAD Mechanical Yield strength not given (tensile used) not given (tensile used) Ultimate tensile strength 221 MPa source typical tensile strength, 25 °C (ACMA Test #4) 115 MPa source tensile strength (ISO 527) Compressive strength 2,068 MPa source typical, 20 °C (ASTM-C773) not sourced Flexural strength 358 MPa source flexural strength (MOR), 20 °C (ASTM-F417) 184 MPa source typical (ISO 178) Elongation at break not sourced 1.5 % source tensile elongation (ISO 527) Young's modulus (stiffness) 303 GPa source typical, 20 °C (ASTM-C848) 11.5 GPa source tensile modulus (ISO 527) Density 3,720 kg/m³ source typical (ASTM-C20) 1,610 kg/m³ source typical Strength to weight 59.4 kN·m/kg 71.4 kN·m/kg 20% higher Stiffness to weight 81.5 MN·m/kg 11.4x higher 7.14 MN·m/kg Poisson's ratio 0.21 source typical, 20 °C (ASTM-C848) not sourced Shear modulus 125 GPa not sourced Bulk modulus 174 GPa not sourced Speed of sound 9,025 m/s 2,673 m/s Thermal Thermal conductivity 24.7 W/m·K source typical, 20 °C (ASTM-C408) 0.5 W/m·K source hot disk (ISO 22007-2), temperature not stated Thermal expansion 8.2 µm/m·K source mean, 25-1000 °C (ASTM-C372) 20 µm/m·K source flow direction (MD), mean 50-150 °C 100 mm part over a 50 °C swing 41 µm growth 2.44x less 100 µm growth Specific heat 880 J/kg·K source typical, 100 °C (ASTM-E1269) 839 J/kg·K source ASTM E1269, temperature not stated Heats up and cools (diffusivity) 7.55 mm²/s 20.4x faster 0.37 mm²/s Thermal shock resistance 1,736 W/m not sourced Max service temperature not sourced 288 °C source HDT 1.8 MPa (ISO 75) Values for CoorsTek AD-96, nominal 96% Al2O3 sintered alumina, typical values; CoorsTek "Ceramic Seal Material Properties" (© 2018, 01899 F). AD-96 is the general 96% grade, not the ADS-96R substrate grade. Sumitomo Chemical SUMIKASUPER LCP E6006L (30% glass fibre; high strength, low shrinkage); SUMIKASUPER LCP Technical Note, Version 04 / Nov. 2023, typical values.
Every value links to the document that states it. "Not sourced" means no citable source states it (or only a specification minimum); figures computed from it are left out too.
Questions Is Ceramic Alumina 96% stronger than Plastic LCP GF30? Ceramic Alumina 96% is stronger: its tensile strength is 221 MPa against 115 MPa for Plastic LCP GF30 (1.92x).
Which is lighter, Ceramic Alumina 96% or Plastic LCP GF30? Plastic LCP GF30 is lighter: 1,610 kg/m³ against 3,720 kg/m³ for Ceramic Alumina 96%.
Which is stiffer, Ceramic Alumina 96% or Plastic LCP GF30? Ceramic Alumina 96% is stiffer: Young's modulus 303 GPa against 11.5 GPa for Plastic LCP GF30, so the same part in Ceramic Alumina 96% deflects less under the same load.
Which is lighter for the same job, Ceramic Alumina 96% or Plastic LCP GF30? For the same stiffness or strength: Ceramic Alumina 96% is lighter for a stiff rod or tie (tension), stiff beam (bending), stiff panel or plate; Plastic LCP GF30 is lighter for a strong rod or tie, strong beam, strong panel or plate.
Part that must be Ceramic Alumina 96% Plastic LCP GF30 Stiff rod or tie (tension) lighter 11.4x heavier Stiff beam (bending) lighter 2.22x heavier Stiff panel or plate lighter 29% heavier Strong rod or tie 20% heavier lighter Strong beam 49% heavier lighter Strong panel or plate 1.67x heavier lighter
For the same stiffness or strength, mass scales with density over stiffness (or strength) raised to a power set by how the part is loaded: 1 for a rod in tension, 1/2 for a beam in bending, 1/3 for a panel (the standard material-selection indices).
Which conducts heat better, Ceramic Alumina 96% or Plastic LCP GF30? Ceramic Alumina 96% conducts heat better: 24.7 W/m·K against 0.5 W/m·K for Plastic LCP GF30.
Which expands less with temperature? Ceramic Alumina 96% expands less: 8.2 µm/m·K against 20 µm/m·K for Plastic LCP GF30.
Among 72 materials 1k 10k 0.1 1 10 100 Density (kg/m³) Young's modulus (GPa) Plastic PLA Plastic PETG Plastic ABS Plastic TPU Plastic Nylon Aluminum Steel Iron Titanium Steel AISI 1018 Stainless Steel 304 Stainless Steel 316 Aluminum 6061-T6 Aluminum 7075-T6 Brass C360 Copper C110 Glass Steel AISI 1045 Steel AISI 4340 Steel A992 Stainless Steel 303 Stainless Steel 17-4PH Aluminum 2024-T351 Aluminum 5052-H32 Aluminum 7050-T7451 Titanium Ti-6Al-4V Brass C260 Nickel Inconel 718 Magnesium AZ31B-H24 Zinc Zamak 3 Plastic ABS (bulk/injection) Plastic Polycarbonate Plastic POM/Acetal Plastic Nylon PA6 Plastic Nylon PA66 Plastic PEEK Plastic UHMWPE Plastic HDPE Plastic Polypropylene Plastic PMMA FDM ASA FDM Polycarbonate FDM PAHT-CF FDM HIPS SLA Resin Tough 2000 SLS PA12 Nylon DMLS AlSi10Mg Aluminum DMLS Ti-6Al-4V ELI Titanium DMLS 316L Stainless Steel DMLS 17-4PH Stainless Steel PCB Laminate FR-4 Silicon Ceramic Aluminum Nitride Aluminum A380 Aluminum 6063-T6 Aluminum 1100-O Aluminum ADC12 Magnesium AZ91D Solder SAC305 Plastic PBT GF30 Plastic PPS GF40 Ceramic Alumina 96% Plastic LCP GF30 Stiffness against density 1k 10k 10 100 1k Density (kg/m³) Yield strength (MPa) Plastic PLA Plastic PETG Plastic ABS Plastic TPU Plastic Nylon Rubber Aluminum Steel Iron Titanium Steel AISI 1018 Stainless Steel 304 Stainless Steel 316 Aluminum 6061-T6 Aluminum 7075-T6 Brass C360 Copper C110 Glass Steel AISI 1045 Steel AISI 4340 Steel A992 Stainless Steel 303 Stainless Steel 17-4PH Aluminum 2024-T351 Aluminum 5052-H32 Aluminum 7050-T7451 Titanium Ti-6Al-4V Brass C260 Nickel Inconel 718 Magnesium AZ31B-H24 Zinc Zamak 3 Plastic ABS (bulk/injection) Plastic Polycarbonate Plastic POM/Acetal Plastic Nylon PA6 Plastic Nylon PA66 Plastic PEEK Plastic PTFE Plastic UHMWPE Plastic HDPE Plastic Polypropylene Plastic PMMA FDM ASA FDM Polycarbonate FDM PAHT-CF FDM HIPS SLA Resin Tough 2000 SLA Resin Elastic 50A SLS PA12 Nylon DMLS AlSi10Mg Aluminum DMLS Ti-6Al-4V ELI Titanium DMLS 316L Stainless Steel DMLS 17-4PH Stainless Steel Brick PCB Laminate FR-4 Silicon Aluminum A380 Aluminum 6063-T6 Aluminum 1100-O Aluminum ADC12 Magnesium AZ91D Solder SAC305 Plastic PBT GF30 Plastic PPS GF40 Ceramic Alumina 96% Plastic LCP GF30 Strength against density