Materials / Compare
DMLS Ti-6Al-4V ELI Titanium vs. Plastic Polypropylene
Compare DMLS Ti-6Al-4V ELI Titanium vs. Plastic Polypropylene strength, stiffness, weight and thermal properties.
| Mechanical | DMLS Ti-6Al-4V ELI Titanium | Plastic Polypropylene |
|---|---|---|
| Yield strength | 1,100MPa133.3x stronger | 33MPa2 |
| Ultimate tensile strength | 1,270MPa1 | not stated (yield given) |
| Elongation at break | 8.7%1 | not sourced |
| Young's modulus (stiffness) | same maker and process110GPa375.9x stiffer | 1.45GPa2 |
| Density | 4,400kg/m³1 | 900kg/m³24.89x lighter |
| Strength to weight | 250kN·m/kg6.82x higher | 36.7kN·m/kg |
| Stiffness to weight | 25MN·m/kg15.5x higher | 1.61MN·m/kg |
| Poisson's ratio | wrought TIMETAL 6-40.3424 | base material0.425 |
| Shear modulus | 41GPa80.3x stiffer in shear | 0.511GPa |
| Bulk modulus | 116GPa38.4x higher | 3.02GPa |
| Speed of sound | 5,000m/s3.94x faster | 1,269m/s |
| Thermal | DMLS Ti-6Al-4V ELI Titanium | Plastic Polypropylene |
|---|---|---|
| Thermal conductivity | base material6.6W/m·K6 | base material0.17–0.22W/m·K5 |
| Thermal expansion | mean 25-100 °C9µm/m·K7 | base material80–100µm/m·K5 |
| 100 mm part over a 50 °C swing | 45µm growth10x less | 450µm growth |
| Specific heat | base material580J/kg·K6 | not sourced |
| Heats up and cools (diffusivity) | 2.59mm²/s | not sourced |
| Thermal shock resistance | 4,825W/m169x more resistant | 28.6W/m |
| Melting point | melting range1,630–1,650°C4 | not sourced |
| Max service temperature | not sourced | HDT 0.45 MPa90°C2 |
| Try it on a partA bracket to run stress or thermal on, free in your browser | Open in LessCAD | Open in LessCAD |
|---|
Sources7 documents: EOS GmbH, LyondellBasell, TIMET, INEOS Olefins & Polymers USA
- DMLS Ti-6Al-4V ELI Titanium
- EOS Titanium Ti64ELI (powder 9011-0040; ASTM F136/F3001, i.e. Grade 23) on EOS M400 SF, parameter set Ti64ELI_030_FlexM400_100, 30 µm, as built; ISO 6892-1 A14
- Plastic Polypropylene
- LyondellBasell Moplen HP501H polypropylene homopolymer (general purpose), typical ISO values
- 1EOS Titanium Ti64ELI Material Data Sheet, M 290 and M 400EOS GmbHarchived copyDMLS Ti-6Al-4V ELI Titanium · Yield strength: typical, as built, average of horizontal + vertical (M400)DMLS Ti-6Al-4V ELI Titanium · Ultimate tensile strength: typical, as built, average of horizontal + vertical (M400)DMLS Ti-6Al-4V ELI Titanium · Elongation at break: typical at break, as built (M400)DMLS Ti-6Al-4V ELI Titanium · Density: typical part density (ISO 3369), M400
- 2Moplen HP501H Product DataLyondellBasellPlastic Polypropylene · Yield strength: typical, tensile stress at yield ISO 527Plastic Polypropylene · Young's modulus (stiffness): typical, tensile modulus ISO 527Plastic Polypropylene · Density: typical, 23 °C ISO 1183-1Plastic Polypropylene · Max service temperature: HDT 0.45 MPa (ISO 75B), unannealed
- 3EOS Titanium Ti64 Material Data Sheet, M 290 (2022)EOS GmbHarchived copyDMLS Ti-6Al-4V ELI Titanium · Young's modulus (stiffness): same maker and process, sibling grade: EOS Titanium Ti64 (Grade 5) on EOS M 290, as built, XY and Z, typical
- 4TIMETAL 6-4 PropertiesTIMETarchived copyDMLS Ti-6Al-4V ELI Titanium · Poisson's ratio: wrought TIMETAL 6-4 (TIMET measurement, mean of 10); composition-level, not DMLS-measuredDMLS Ti-6Al-4V ELI Titanium · Melting point: melting range, wrought TIMETAL 6-4 (composition-level)
- 5Typical Engineering Properties of PolypropyleneINEOS Olefins & Polymers USAarchived copyPlastic Polypropylene · Poisson's ratio: base material: polypropylene homopolymer family (INEOS Olefins & Polymers USA, Typical Engineering Properties of Polypropylene)Plastic Polypropylene · Thermal conductivity: base material: polypropylene homopolymer family (INEOS Olefins & Polymers USA, Typical Engineering Properties of Polypropylene)Plastic Polypropylene · Thermal expansion: base material: polypropylene homopolymer family (INEOS Olefins & Polymers USA, Typical Engineering Properties of Polypropylene)
- 6TIMETAL 6-4 Data SheetTIMETarchived copyDMLS Ti-6Al-4V ELI Titanium · Thermal conductivity: base material: wrought Ti-6Al-4V / 6-4 ELI (TIMET datasheet), 20 °CDMLS Ti-6Al-4V ELI Titanium · Specific heat: base material: wrought Ti-6Al-4V / 6-4 ELI (TIMET datasheet), 20 °C
- 7EOS Titanium Ti64 Grade 23 Material Data SheetEOS GmbHarchived copyDMLS Ti-6Al-4V ELI Titanium · Thermal expansion: mean 25-100 °C, ASTM E228; EOS Ti64 Grade 23 (=ELI) on EOS M 290 40 µm; condition not stated (sheet's mechanical data are heat treated)
Each number points to the document that states it, with the exact basis. Values without a number are computed from the sourced ones. "Not sourced" means no citable source states it (or only a specification minimum); figures computed from it are left out too.
DMLS Ti-6Al-4V ELI Titanium is 3D printed: its properties depend on build direction and print settings; these are typical values.
Questions
Mechanical
Is DMLS Ti-6Al-4V ELI Titanium stronger than Plastic Polypropylene?
DMLS Ti-6Al-4V ELI Titanium is stronger: its yield strength is 1,100 MPa against 33 MPa for Plastic Polypropylene (33.3x).
Which is lighter, DMLS Ti-6Al-4V ELI Titanium or Plastic Polypropylene?
Plastic Polypropylene is lighter: 900 kg/m³ against 4,400 kg/m³ for DMLS Ti-6Al-4V ELI Titanium.
Which is stiffer, DMLS Ti-6Al-4V ELI Titanium or Plastic Polypropylene?
DMLS Ti-6Al-4V ELI Titanium is stiffer: Young's modulus 110 GPa against 1.45 GPa for Plastic Polypropylene, so the same part in DMLS Ti-6Al-4V ELI Titanium deflects less under the same load.
Which is lighter for the same job, DMLS Ti-6Al-4V ELI Titanium or Plastic Polypropylene?
For the same stiffness or strength: DMLS Ti-6Al-4V ELI Titanium is lighter for a stiff rod or tie (tension), stiff beam (bending), strong rod or tie, strong beam, strong panel or plate; Plastic Polypropylene is lighter for a stiff panel or plate.
| Part that must be | DMLS Ti-6Al-4V ELI Titanium | Plastic Polypropylene |
|---|---|---|
| Stiff rod or tie (tension) | lighter | 15.5x heavier |
| Stiff beam (bending) | lighter | 1.78x heavier |
| Stiff panel or plate | 15% heavier | lighter |
| Strong rod or tie | lighter | 6.82x heavier |
| Strong beam | lighter | 2.12x heavier |
| Strong panel or plate | lighter | 18% heavier |
For the same stiffness or strength, mass scales with density over stiffness (or strength) raised to a power set by how the part is loaded: 1 for a rod in tension, 1/2 for a beam in bending, 1/3 for a panel (the standard material-selection indices).
Thermal
Which conducts heat better, DMLS Ti-6Al-4V ELI Titanium or Plastic Polypropylene?
DMLS Ti-6Al-4V ELI Titanium conducts heat better: 6.6 W/m·K against 0.195 W/m·K for Plastic Polypropylene.
Which expands less with temperature?
DMLS Ti-6Al-4V ELI Titanium expands less: 9 µm/m·K against 90 µm/m·K for Plastic Polypropylene.
Related comparisons
- DMLS Ti-6Al-4V ELI Titanium vs. Titanium
- DMLS Ti-6Al-4V ELI Titanium vs. Titanium Ti-6Al-4V
- DMLS Ti-6Al-4V ELI Titanium vs. Stainless Steel 17-4PH
- DMLS Ti-6Al-4V ELI Titanium vs. Steel AISI 4340
- Plastic Polypropylene vs. SLA Resin Tough 2000
- Plastic Polypropylene vs. Plastic ABS
- Plastic Polypropylene vs. SLS PA12 Nylon
- Plastic Polypropylene vs. Rubber