Thermal conductivity against densityHigher and further left: spreads more heat for its weightThermal expansion against thermal conductivityLower and further right: warps less when heated
Try it on a partA bracket to run stress or thermal on, free in your browser
Sources4 documents: Cleveland-Cliffs, Bambu Lab, National Institute of Standards and Technology, INEOS Styrolution
FDM ASA
Bambu Lab ASA, TDS V3.0, printed specimens X-Y; nozzle 260 °C, bed 80 °C, 200 mm/s, 100% infill; annealed and dried 80 °C for 12 h before testing.
Iron
Cleveland-Cliffs / AK Steel ARMCO Pure Iron Product Data Bulletin (07/2022): Table 1 typical physical properties, Table 2 typical mechanical properties after SRA/recrystallization anneal.
1
ARMCO Pure Iron Product Data Bulletin (2022)Cleveland-Cliffsarchived copyIron · Yield strength: typical (0.2% YS), hot rolled + SRA/recrystallization annealIron · Ultimate tensile strength: typical, SRA/recrystallization annealIron · Elongation at break: typical, gauge 4D0Iron · Young's modulus (stiffness): typical, after SRA/recrystallization annealIron · Density: typicalIron · Thermal conductivity: typical at 20 °CIron · Thermal expansion: mean, 20-399 °CIron · Specific heat: typicalIron · Melting point: typical
Elastic Properties of Metals and Alloys, I. Iron, Nickel, and Iron-Nickel Alloys, J. Phys. Chem. Ref. Data 2 (1973)National Institute of Standards and Technologyarchived copyIron · Poisson's ratio: NIST critically evaluated best value (polycrystalline iron)
4
Luran S 777K (ASA) Product Data SheetINEOS StyrolutionFDM ASA · Thermal conductivity: base material: INEOS Styrolution Luran S 777K injection-molding ASA, typicalFDM ASA · Thermal expansion: base material: INEOS Styrolution Luran S 777K injection-molding ASA, range
Each number points to the document that states it, with the exact basis. Values without a number are computed from the sourced ones. "Not sourced" means no citable source states it (or only a specification minimum); figures computed from it are left out too.
FDM ASA is 3D printed: its properties depend on build direction and print settings; these are typical values.
Questions
Mechanical
Is FDM ASA stronger than Iron?
Iron is stronger: its yield strength is 186 MPa against tensile strength 37 MPa for FDM ASA (5.03x).
Which is lighter, FDM ASA or Iron?
FDM ASA is lighter: 1,050 kg/m³ against 7,860 kg/m³ for Iron.
Which is stiffer, FDM ASA or Iron?
Iron is stiffer: Young's modulus 207 GPa against 2.45 GPa for FDM ASA, so the same part in Iron deflects less under the same load.
Which is lighter for the same job, FDM ASA or Iron?
For the same stiffness or strength: FDM ASA is lighter for a stiff panel or plate, strong rod or tie, strong beam, strong panel or plate; Iron is lighter for a stiff rod or tie (tension), stiff beam (bending).
Part that must be
FDM ASA
Iron
Stiff rod or tie (tension)
11.3x heavier
lighter
Stiff beam (bending)
23% heavier
lighter
Stiff panel or plate
lighter
1.71x heavier
Strong rod or tie
lighter
49% heavier
Strong beam
lighter
2.55x heavier
Strong panel or plate
lighter
3.34x heavier
For the same stiffness or strength, mass scales with density over stiffness (or strength) raised to a power set by how the part is loaded: 1 for a rod in tension, 1/2 for a beam in bending, 1/3 for a panel (the standard material-selection indices).
Which is more ductile, FDM ASA or Iron?
Iron stretches further before it breaks: 38% elongation at break against 9.2% for FDM ASA.
Thermal
Which conducts heat better, FDM ASA or Iron?
Iron conducts heat better: 73.2 W/m·K against 0.17 W/m·K for FDM ASA.
Which expands less with temperature?
Iron expands less: 13.7 µm/m·K against 95 µm/m·K for FDM ASA.