Thermal conductivity against densityHigher and further left: spreads more heat for its weightThermal expansion against thermal conductivityLower and further right: warps less when heated
Try it on a partA bracket to run stress or thermal on, free in your browser
Sources4 documents: Cleveland-Cliffs, BASF, National Institute of Standards and Technology, Covestro
Iron
Cleveland-Cliffs / AK Steel ARMCO Pure Iron Product Data Bulletin (07/2022): Table 1 typical physical properties, Table 2 typical mechanical properties after SRA/recrystallization anneal.
Plastic Nylon PA66
BASF Ultramid A3K (PA66, unreinforced injection-moulding grade), Product Information 02/2026, dry values (ISO methods)
1
ARMCO Pure Iron Product Data Bulletin (2022)Cleveland-Cliffsarchived copyIron · Yield strength: typical (0.2% YS), hot rolled + SRA/recrystallization annealIron · Ultimate tensile strength: typical, SRA/recrystallization annealIron · Elongation at break: typical, gauge 4D0Iron · Young's modulus (stiffness): typical, after SRA/recrystallization annealIron · Density: typicalIron · Thermal conductivity: typical at 20 °CIron · Thermal expansion: mean, 20-399 °CIron · Specific heat: typicalIron · Melting point: typical
Elastic Properties of Metals and Alloys, I. Iron, Nickel, and Iron-Nickel Alloys, J. Phys. Chem. Ref. Data 2 (1973)National Institute of Standards and Technologyarchived copyIron · Poisson's ratio: NIST critically evaluated best value (polycrystalline iron)
4
Engineering Polymers Part and Mold Design: Thermoplastics, A Design GuideCovestroPlastic Nylon PA66 · Poisson's ratio: base material: unfilled polyamide (PA), conditioned, maker design-guide family value (Covestro Table 3-1)
Each number points to the document that states it, with the exact basis. Values without a number are computed from the sourced ones. "Not sourced" means no citable source states it (or only a specification minimum); figures computed from it are left out too.
Questions
Mechanical
Is Iron stronger than Plastic Nylon PA66?
Iron is stronger: its yield strength is 186 MPa against 85 MPa for Plastic Nylon PA66 (2.19x).
Which is lighter, Iron or Plastic Nylon PA66?
Plastic Nylon PA66 is lighter: 1,130 kg/m³ against 7,860 kg/m³ for Iron.
Which is stiffer, Iron or Plastic Nylon PA66?
Iron is stiffer: Young's modulus 207 GPa against 3 GPa for Plastic Nylon PA66, so the same part in Iron deflects less under the same load.
Which is lighter for the same job, Iron or Plastic Nylon PA66?
For the same stiffness or strength: Iron is lighter for a stiff rod or tie (tension), stiff beam (bending); Plastic Nylon PA66 is lighter for a stiff panel or plate, strong rod or tie, strong beam, strong panel or plate.
Part that must be
Iron
Plastic Nylon PA66
Stiff rod or tie (tension)
lighter
9.92x heavier
Stiff beam (bending)
lighter
19% heavier
Stiff panel or plate
1.7x heavier
lighter
Strong rod or tie
3.18x heavier
lighter
Strong beam
4.13x heavier
lighter
Strong panel or plate
4.7x heavier
lighter
For the same stiffness or strength, mass scales with density over stiffness (or strength) raised to a power set by how the part is loaded: 1 for a rod in tension, 1/2 for a beam in bending, 1/3 for a panel (the standard material-selection indices).
Which is more ductile, Iron or Plastic Nylon PA66?
Iron stretches further before it breaks: 38% elongation at break against 30% for Plastic Nylon PA66.
Thermal
Which conducts heat better, Iron or Plastic Nylon PA66?
Iron conducts heat better: 73.2 W/m·K against 0.33 W/m·K for Plastic Nylon PA66.
Which expands less with temperature?
Iron expands less: 13.7 µm/m·K against 98 µm/m·K for Plastic Nylon PA66.