Thermal conductivity against densityHigher and further left: spreads more heat for its weightThermal expansion against thermal conductivityLower and further right: warps less when heated
Try it on a partA bracket to run stress or thermal on, free in your browser
Sources4 documents: Cleveland-Cliffs, TIMET, National Institute of Standards and Technology
Iron
Cleveland-Cliffs / AK Steel ARMCO Pure Iron Product Data Bulletin (07/2022): Table 1 typical physical properties, Table 2 typical mechanical properties after SRA/recrystallization anneal.
ARMCO Pure Iron Product Data Bulletin (2022)Cleveland-Cliffsarchived copyIron · Yield strength: typical (0.2% YS), hot rolled + SRA/recrystallization annealIron · Ultimate tensile strength: typical, SRA/recrystallization annealIron · Elongation at break: typical, gauge 4D0Iron · Young's modulus (stiffness): typical, after SRA/recrystallization annealIron · Density: typicalIron · Thermal conductivity: typical at 20 °CIron · Thermal expansion: mean, 20-399 °CIron · Specific heat: typicalIron · Melting point: typical
2
TIMETAL 6-4 PropertiesTIMETarchived copyTitanium Ti-6Al-4V · Yield strength: typical, plate (>0.187 in), annealed, 0.2% offsetTitanium Ti-6Al-4V · Ultimate tensile strength: typical, plate, annealedTitanium Ti-6Al-4V · Elongation at break: typical, in 2 in., plate annealedTitanium Ti-6Al-4V · Density: nominalTitanium Ti-6Al-4V · Poisson's ratio: mean of TIMET measurementsTitanium Ti-6Al-4V · Melting point: melting rangeTitanium Ti-6Al-4V · Max service temperature: upper recommended use temperature
3
TIMETAL 6-4 Data SheetTIMETarchived copyTitanium Ti-6Al-4V · Young's modulus (stiffness): typical range, 20 °CTitanium Ti-6Al-4V · Thermal conductivity: typical, 20 °C, mill annealedTitanium Ti-6Al-4V · Thermal expansion: typical, mean 0-100 °CTitanium Ti-6Al-4V · Specific heat: typical, 20 °C
4
Elastic Properties of Metals and Alloys, I. Iron, Nickel, and Iron-Nickel Alloys, J. Phys. Chem. Ref. Data 2 (1973)National Institute of Standards and Technologyarchived copyIron · Poisson's ratio: NIST critically evaluated best value (polycrystalline iron)
Each number points to the document that states it, with the exact basis. Values without a number are computed from the sourced ones. "Not sourced" means no citable source states it (or only a specification minimum); figures computed from it are left out too.
Questions
Mechanical
Is Iron stronger than Titanium Ti-6Al-4V?
Titanium Ti-6Al-4V is stronger: its yield strength is 885 MPa against 186 MPa for Iron (4.76x).
Which is lighter, Iron or Titanium Ti-6Al-4V?
Titanium Ti-6Al-4V is lighter: 4,430 kg/m³ against 7,860 kg/m³ for Iron.
Which is stiffer, Iron or Titanium Ti-6Al-4V?
Iron is stiffer: Young's modulus 207 GPa against 115 GPa for Titanium Ti-6Al-4V, so the same part in Iron deflects less under the same load.
Which is lighter for the same job, Iron or Titanium Ti-6Al-4V?
For the same stiffness or strength: Iron is lighter for a stiff rod or tie (tension); Titanium Ti-6Al-4V is lighter for a stiff beam (bending), stiff panel or plate, strong rod or tie, strong beam, strong panel or plate.
Part that must be
Iron
Titanium Ti-6Al-4V
Stiff rod or tie (tension)
lighter
2% heavier
Stiff beam (bending)
32% heavier
lighter
Stiff panel or plate
46% heavier
lighter
Strong rod or tie
8.44x heavier
lighter
Strong beam
5.02x heavier
lighter
Strong panel or plate
3.87x heavier
lighter
For the same stiffness or strength, mass scales with density over stiffness (or strength) raised to a power set by how the part is loaded: 1 for a rod in tension, 1/2 for a beam in bending, 1/3 for a panel (the standard material-selection indices).
Which is more ductile, Iron or Titanium Ti-6Al-4V?
Iron stretches further before it breaks: 38% elongation at break against 16% for Titanium Ti-6Al-4V.
Thermal
Which conducts heat better, Iron or Titanium Ti-6Al-4V?
Iron conducts heat better: 73.2 W/m·K against 6.6 W/m·K for Titanium Ti-6Al-4V.
Which expands less with temperature?
Titanium Ti-6Al-4V expands less: 9 µm/m·K against 13.7 µm/m·K for Iron.