Thermal conductivity against densityHigher and further left: spreads more heat for its weightThermal expansion against thermal conductivityLower and further right: warps less when heated
Try it on a partA bracket to run stress or thermal on, free in your browser
1.4305 / UNS S30300, Outokumpu typical values (hot rolled, solution annealed) from 'Steel Grades, Properties and Global Standards'; max service from Carpenter CarTech 303 datasheet
Steel Grades, Properties and Global StandardsOutokumpuarchived copyStainless Steel 303 · Yield strength: Outokumpu typical (product P = hot rolled plate, transverse)Stainless Steel 303 · Ultimate tensile strength: Outokumpu typicalStainless Steel 303 · Elongation at break: Outokumpu typical, A5Stainless Steel 303 · Young's modulus (stiffness): at RT (Table 12)Stainless Steel 303 · Density: at RTStainless Steel 303 · Thermal conductivity: at RTStainless Steel 303 · Thermal expansion: mean, 20–100 °CStainless Steel 303 · Specific heat: at RT
3
Engineering Polymers Part and Mold Design: Thermoplastics, A Design GuideCovestroarchived copyPlastic ABS (bulk/injection) · Poisson's ratio: typical, ABS family (Covestro Part and Mold Design guide, Table 3-1)
4
Design Manual for Structural Stainless Steel, 4th Edition (P413)Steel Construction Institutearchived copyStainless Steel 303 · Poisson's ratio: design value (structural stainless steels)
5
Carpenter Stainless Type 303 Data SheetCarpenter Technologyarchived copyStainless Steel 303 · Max service temperature: continuous, scaling limit
Each number points to the document that states it, with the exact basis. Values without a number are computed from the sourced ones. "Not sourced" means no citable source states it (or only a specification minimum); figures computed from it are left out too.
Questions
Mechanical
Is Plastic ABS (bulk/injection) stronger than Stainless Steel 303?
Stainless Steel 303 is stronger: its yield strength is 275 MPa against 45 MPa for Plastic ABS (bulk/injection) (6.11x).
Which is lighter, Plastic ABS (bulk/injection) or Stainless Steel 303?
Plastic ABS (bulk/injection) is lighter: 1,040 kg/m³ against 7,900 kg/m³ for Stainless Steel 303.
Which is stiffer, Plastic ABS (bulk/injection) or Stainless Steel 303?
Stainless Steel 303 is stiffer: Young's modulus 200 GPa against 2.3 GPa for Plastic ABS (bulk/injection), so the same part in Stainless Steel 303 deflects less under the same load.
Which is lighter for the same job, Plastic ABS (bulk/injection) or Stainless Steel 303?
For the same stiffness or strength: Plastic ABS (bulk/injection) is lighter for a stiff panel or plate, strong rod or tie, strong beam, strong panel or plate; Stainless Steel 303 is lighter for a stiff rod or tie (tension), stiff beam (bending).
Part that must be
Plastic ABS (bulk/injection)
Stainless Steel 303
Stiff rod or tie (tension)
11.4x heavier
lighter
Stiff beam (bending)
23% heavier
lighter
Stiff panel or plate
lighter
1.71x heavier
Strong rod or tie
lighter
24% heavier
Strong beam
lighter
2.27x heavier
Strong panel or plate
lighter
3.07x heavier
For the same stiffness or strength, mass scales with density over stiffness (or strength) raised to a power set by how the part is loaded: 1 for a rod in tension, 1/2 for a beam in bending, 1/3 for a panel (the standard material-selection indices).
Which is more ductile, Plastic ABS (bulk/injection) or Stainless Steel 303?
Stainless Steel 303 stretches further before it breaks: 35% elongation at break against 10% for Plastic ABS (bulk/injection).
Thermal
Which conducts heat better, Plastic ABS (bulk/injection) or Stainless Steel 303?
Stainless Steel 303 conducts heat better: 15 W/m·K against 0.17 W/m·K for Plastic ABS (bulk/injection).
Which expands less with temperature?
Stainless Steel 303 expands less: 16 µm/m·K against 95 µm/m·K for Plastic ABS (bulk/injection).