Thermal conductivity against densityHigher and further left: spreads more heat for its weightThermal expansion against thermal conductivityLower and further right: warps less when heated
Try it on a partA bracket to run stress or thermal on, free in your browser
TIMETAL 6-4 PropertiesTIMETarchived copyTitanium · Yield strength: typical, plate (>0.187 in), annealed, 0.2% offsetTitanium · Ultimate tensile strength: typical, plate, annealedTitanium · Elongation at break: typical, in 2 in., plate annealedTitanium · Density: nominalTitanium · Poisson's ratio: mean of TIMET measurementsTitanium · Melting point: melting rangeTitanium · Max service temperature: upper recommended use temperature
3
TIMETAL 6-4 Data SheetTIMETarchived copyTitanium · Young's modulus (stiffness): typical range, 20 °CTitanium · Thermal conductivity: typical, 20 °C, mill annealedTitanium · Thermal expansion: typical, mean 0-100 °CTitanium · Specific heat: typical, 20 °C
4
Engineering Polymers Part and Mold Design: Thermoplastics, A Design GuideCovestroarchived copyPlastic ABS (bulk/injection) · Poisson's ratio: typical, ABS family (Covestro Part and Mold Design guide, Table 3-1)
Each number points to the document that states it, with the exact basis. Values without a number are computed from the sourced ones. "Not sourced" means no citable source states it (or only a specification minimum); figures computed from it are left out too.
Questions
Mechanical
Is Plastic ABS (bulk/injection) stronger than Titanium?
Titanium is stronger: its yield strength is 885 MPa against 45 MPa for Plastic ABS (bulk/injection) (19.7x).
Which is lighter, Plastic ABS (bulk/injection) or Titanium?
Plastic ABS (bulk/injection) is lighter: 1,040 kg/m³ against 4,430 kg/m³ for Titanium.
Which is stiffer, Plastic ABS (bulk/injection) or Titanium?
Titanium is stiffer: Young's modulus 115 GPa against 2.3 GPa for Plastic ABS (bulk/injection), so the same part in Titanium deflects less under the same load.
Which is lighter for the same job, Plastic ABS (bulk/injection) or Titanium?
For the same stiffness or strength: Plastic ABS (bulk/injection) is lighter for a stiff panel or plate; Titanium is lighter for a stiff rod or tie (tension), stiff beam (bending), strong rod or tie, strong beam, strong panel or plate.
Part that must be
Plastic ABS (bulk/injection)
Titanium
Stiff rod or tie (tension)
11.7x heavier
lighter
Stiff beam (bending)
1.66x heavier
lighter
Stiff panel or plate
lighter
16% heavier
Strong rod or tie
4.62x heavier
lighter
Strong beam
1.71x heavier
lighter
Strong panel or plate
4% heavier
lighter
For the same stiffness or strength, mass scales with density over stiffness (or strength) raised to a power set by how the part is loaded: 1 for a rod in tension, 1/2 for a beam in bending, 1/3 for a panel (the standard material-selection indices).
Which is more ductile, Plastic ABS (bulk/injection) or Titanium?
Titanium stretches further before it breaks: 16% elongation at break against 10% for Plastic ABS (bulk/injection).
Thermal
Which conducts heat better, Plastic ABS (bulk/injection) or Titanium?
Titanium conducts heat better: 6.6 W/m·K against 0.17 W/m·K for Plastic ABS (bulk/injection).
Which expands less with temperature?
Titanium expands less: 9 µm/m·K against 95 µm/m·K for Plastic ABS (bulk/injection).