Thermal conductivity against densityHigher and further left: spreads more heat for its weightThermal expansion against thermal conductivityLower and further right: warps less when heated
Try it on a partA bracket to run stress or thermal on, free in your browser
Sources5 documents: BASF, Outokumpu, Covestro, Steel Construction Institute, Carpenter Technology
Plastic Nylon PA66
BASF Ultramid A3K (PA66, unreinforced injection-moulding grade), Product Information 02/2026, dry values (ISO methods)
Stainless Steel 303
1.4305 / UNS S30300, Outokumpu typical values (hot rolled, solution annealed) from 'Steel Grades, Properties and Global Standards'; max service from Carpenter CarTech 303 datasheet
Steel Grades, Properties and Global StandardsOutokumpuarchived copyStainless Steel 303 · Yield strength: Outokumpu typical (product P = hot rolled plate, transverse)Stainless Steel 303 · Ultimate tensile strength: Outokumpu typicalStainless Steel 303 · Elongation at break: Outokumpu typical, A5Stainless Steel 303 · Young's modulus (stiffness): at RT (Table 12)Stainless Steel 303 · Density: at RTStainless Steel 303 · Thermal conductivity: at RTStainless Steel 303 · Thermal expansion: mean, 20–100 °CStainless Steel 303 · Specific heat: at RT
3
Engineering Polymers Part and Mold Design: Thermoplastics, A Design GuideCovestroPlastic Nylon PA66 · Poisson's ratio: base material: unfilled polyamide (PA), conditioned, maker design-guide family value (Covestro Table 3-1)
4
Design Manual for Structural Stainless Steel, 4th Edition (P413)Steel Construction Institutearchived copyStainless Steel 303 · Poisson's ratio: design value (structural stainless steels)
5
Carpenter Stainless Type 303 Data SheetCarpenter Technologyarchived copyStainless Steel 303 · Max service temperature: continuous, scaling limit
Each number points to the document that states it, with the exact basis. Values without a number are computed from the sourced ones. "Not sourced" means no citable source states it (or only a specification minimum); figures computed from it are left out too.
Questions
Mechanical
Is Plastic Nylon PA66 stronger than Stainless Steel 303?
Stainless Steel 303 is stronger: its yield strength is 275 MPa against 85 MPa for Plastic Nylon PA66 (3.24x).
Which is lighter, Plastic Nylon PA66 or Stainless Steel 303?
Plastic Nylon PA66 is lighter: 1,130 kg/m³ against 7,900 kg/m³ for Stainless Steel 303.
Which is stiffer, Plastic Nylon PA66 or Stainless Steel 303?
Stainless Steel 303 is stiffer: Young's modulus 200 GPa against 3 GPa for Plastic Nylon PA66, so the same part in Stainless Steel 303 deflects less under the same load.
Which is lighter for the same job, Plastic Nylon PA66 or Stainless Steel 303?
For the same stiffness or strength: Plastic Nylon PA66 is lighter for a stiff panel or plate, strong rod or tie, strong beam, strong panel or plate; Stainless Steel 303 is lighter for a stiff rod or tie (tension), stiff beam (bending).
Part that must be
Plastic Nylon PA66
Stainless Steel 303
Stiff rod or tie (tension)
9.54x heavier
lighter
Stiff beam (bending)
17% heavier
lighter
Stiff panel or plate
lighter
1.72x heavier
Strong rod or tie
lighter
2.16x heavier
Strong beam
lighter
3.2x heavier
Strong panel or plate
lighter
3.89x heavier
For the same stiffness or strength, mass scales with density over stiffness (or strength) raised to a power set by how the part is loaded: 1 for a rod in tension, 1/2 for a beam in bending, 1/3 for a panel (the standard material-selection indices).
Which is more ductile, Plastic Nylon PA66 or Stainless Steel 303?
Stainless Steel 303 stretches further before it breaks: 35% elongation at break against 30% for Plastic Nylon PA66.
Thermal
Which handles higher temperatures, Plastic Nylon PA66 or Stainless Steel 303?
Stainless Steel 303 does: 871 °C against 101 °C for Plastic Nylon PA66.
Which conducts heat better, Plastic Nylon PA66 or Stainless Steel 303?
Stainless Steel 303 conducts heat better: 15 W/m·K against 0.33 W/m·K for Plastic Nylon PA66.
Which expands less with temperature?
Stainless Steel 303 expands less: 16 µm/m·K against 98 µm/m·K for Plastic Nylon PA66.