Thermal conductivity against densityHigher and further left: spreads more heat for its weightThermal expansion against thermal conductivityLower and further right: warps less when heated
Try it on a partA bracket to run stress or thermal on, free in your browser
MIL-HDBK-5J, Metallic Materials and Elements for Aerospace Vehicle Structures (2003)U.S. Department of DefenseSteel AISI 1018 · Young's modulus (stiffness): base material: AISI 1025 plain carbon steel (MIL-HDBK-5J design value; ASTM A108 bar is the cold-finished carbon-steel bar spec that also covers 1018)Steel AISI 1018 · Density: base material: AISI 1025 plain carbon steel (MIL-HDBK-5J design value; ASTM A108 bar is the cold-finished carbon-steel bar spec that also covers 1018)Steel AISI 1018 · Poisson's ratio: base material: AISI 1025 plain carbon steel (MIL-HDBK-5J design value; ASTM A108 bar is the cold-finished carbon-steel bar spec that also covers 1018)Steel AISI 1018 · Thermal conductivity: base material: AISI 1025 plain carbon steel (MIL-HDBK-5J design value; ASTM A108 bar is the cold-finished carbon-steel bar spec that also covers 1018)Steel AISI 1018 · Specific heat: base material: AISI 1025 plain carbon steel (MIL-HDBK-5J design value; ASTM A108 bar is the cold-finished carbon-steel bar spec that also covers 1018)
4
Engineering Polymers Part and Mold Design: Thermoplastics, A Design GuideCovestroPlastic Nylon PA66 · Poisson's ratio: base material: unfilled polyamide (PA), conditioned, maker design-guide family value (Covestro Table 3-1)
5
S275JR Steel GradeOvakoSteel AISI 1018 · Thermal expansion: base material: unalloyed carbon steel, Ovako family table (S275JR, 'none alloyed structural steels', C <= 0.21%); mean 20-300 °C
Each number points to the document that states it, with the exact basis. Values without a number are computed from the sourced ones. "Not sourced" means no citable source states it (or only a specification minimum); figures computed from it are left out too.
Questions
Mechanical
Is Plastic Nylon PA66 stronger than Steel AISI 1018?
Steel AISI 1018 is stronger: its yield strength is 372 MPa against 85 MPa for Plastic Nylon PA66 (4.38x).
Which is lighter, Plastic Nylon PA66 or Steel AISI 1018?
Plastic Nylon PA66 is lighter: 1,130 kg/m³ against 7,861 kg/m³ for Steel AISI 1018.
Which is stiffer, Plastic Nylon PA66 or Steel AISI 1018?
Steel AISI 1018 is stiffer: Young's modulus 200 GPa against 3 GPa for Plastic Nylon PA66, so the same part in Steel AISI 1018 deflects less under the same load.
Which is lighter for the same job, Plastic Nylon PA66 or Steel AISI 1018?
For the same stiffness or strength: Plastic Nylon PA66 is lighter for a stiff panel or plate, strong rod or tie, strong beam, strong panel or plate; Steel AISI 1018 is lighter for a stiff rod or tie (tension), stiff beam (bending).
Part that must be
Plastic Nylon PA66
Steel AISI 1018
Stiff rod or tie (tension)
9.58x heavier
lighter
Stiff beam (bending)
17% heavier
lighter
Stiff panel or plate
lighter
1.72x heavier
Strong rod or tie
lighter
1.59x heavier
Strong beam
lighter
2.6x heavier
Strong panel or plate
lighter
3.33x heavier
For the same stiffness or strength, mass scales with density over stiffness (or strength) raised to a power set by how the part is loaded: 1 for a rod in tension, 1/2 for a beam in bending, 1/3 for a panel (the standard material-selection indices).
Which is more ductile, Plastic Nylon PA66 or Steel AISI 1018?
Plastic Nylon PA66 stretches further before it breaks: 30% elongation at break against 15% for Steel AISI 1018.
Thermal
Which conducts heat better, Plastic Nylon PA66 or Steel AISI 1018?
Steel AISI 1018 conducts heat better: 51.9 W/m·K against 0.33 W/m·K for Plastic Nylon PA66.
Which expands less with temperature?
Steel AISI 1018 expands less: 12 µm/m·K against 98 µm/m·K for Plastic Nylon PA66.