Thermal conductivity against densityHigher and further left: spreads more heat for its weightThermal expansion against thermal conductivityLower and further right: warps less when heated
Try it on a partA bracket to run stress or thermal on, free in your browser
Formlabs Tough 2000 Resin V2 (FLTO2002), TDS Rev. 01 10/06/2025; printed on Form 4 at 100 µm, washed in Form Wash V2 10+5 min in >=99% IPA, post-cured 70 °C for 12 min in Form Cure V2. Orientation not stated.
TIMETAL 6-4 PropertiesTIMETarchived copyTitanium · Yield strength: typical, plate (>0.187 in), annealed, 0.2% offsetTitanium · Ultimate tensile strength: typical, plate, annealedTitanium · Elongation at break: typical, in 2 in., plate annealedTitanium · Density: nominalTitanium · Poisson's ratio: mean of TIMET measurementsTitanium · Melting point: melting rangeTitanium · Max service temperature: upper recommended use temperature
3
TIMETAL 6-4 Data SheetTIMETarchived copyTitanium · Young's modulus (stiffness): typical range, 20 °CTitanium · Thermal conductivity: typical, 20 °C, mill annealedTitanium · Thermal expansion: typical, mean 0-100 °CTitanium · Specific heat: typical, 20 °C
Each number points to the document that states it, with the exact basis. Values without a number are computed from the sourced ones. "Not sourced" means no citable source states it (or only a specification minimum); figures computed from it are left out too.
SLA Resin Tough 2000 is 3D printed: its properties depend on build direction and print settings; these are typical values.
Questions
Mechanical
Is SLA Resin Tough 2000 stronger than Titanium?
Titanium is stronger: its yield strength is 885 MPa against 40.4 MPa for SLA Resin Tough 2000 (21.9x).
Which is lighter, SLA Resin Tough 2000 or Titanium?
SLA Resin Tough 2000 is lighter: 1,090 kg/m³ against 4,430 kg/m³ for Titanium.
Which is stiffer, SLA Resin Tough 2000 or Titanium?
Titanium is stiffer: Young's modulus 115 GPa against 1.8 GPa for SLA Resin Tough 2000, so the same part in Titanium deflects less under the same load.
Which is lighter for the same job, SLA Resin Tough 2000 or Titanium?
For the same stiffness or strength: SLA Resin Tough 2000 is lighter for a stiff panel or plate; Titanium is lighter for a stiff rod or tie (tension), stiff beam (bending), strong rod or tie, strong beam, strong panel or plate.
Part that must be
SLA Resin Tough 2000
Titanium
Stiff rod or tie (tension)
15.7x heavier
lighter
Stiff beam (bending)
1.96x heavier
lighter
Stiff panel or plate
lighter
2% heavier
Strong rod or tie
5.39x heavier
lighter
Strong beam
1.93x heavier
lighter
Strong panel or plate
15% heavier
lighter
For the same stiffness or strength, mass scales with density over stiffness (or strength) raised to a power set by how the part is loaded: 1 for a rod in tension, 1/2 for a beam in bending, 1/3 for a panel (the standard material-selection indices).
Which is more ductile, SLA Resin Tough 2000 or Titanium?
SLA Resin Tough 2000 stretches further before it breaks: 79% elongation at break against 16% for Titanium.
Thermal
Which expands less with temperature?
Titanium expands less: 9 µm/m·K against 134 µm/m·K for SLA Resin Tough 2000.