Thermal conductivity against densityHigher and further left: spreads more heat for its weightThermal expansion against thermal conductivityLower and further right: warps less when heated
Try it on a partA bracket to run stress or thermal on, free in your browser
Alloy 7075 Sheet, Coil & Plate Technical DataKaiser Aluminumarchived copyAluminum 7075-T6 · Density: nominalAluminum 7075-T6 · Thermal conductivity: typical, 20 °C, T651Aluminum 7075-T6 · Thermal expansion: typical, mean 20-100 °CAluminum 7075-T6 · Specific heat: typical, at 100 °CAluminum 7075-T6 · Melting point: melting range
4
MIL-HDBK-5J, Metallic Materials and Elements for Aerospace Vehicle Structures (2003)U.S. Department of DefenseAluminum 7075-T6 · Poisson's ratio: typical (handbook physical constant)
5
Engineering Polymers Part and Mold Design: Thermoplastics, A Design GuideCovestroPlastic Nylon PA66 · Poisson's ratio: base material: unfilled polyamide (PA), conditioned, maker design-guide family value (Covestro Table 3-1)
Each number points to the document that states it, with the exact basis. Values without a number are computed from the sourced ones. "Not sourced" means no citable source states it (or only a specification minimum); figures computed from it are left out too.
Questions
Mechanical
Is Aluminum 7075-T6 stronger than Plastic Nylon PA66?
Aluminum 7075-T6 is stronger: its yield strength is 503 MPa against 85 MPa for Plastic Nylon PA66 (5.92x).
Which is lighter, Aluminum 7075-T6 or Plastic Nylon PA66?
Plastic Nylon PA66 is lighter: 1,130 kg/m³ against 2,800 kg/m³ for Aluminum 7075-T6.
Which is stiffer, Aluminum 7075-T6 or Plastic Nylon PA66?
Aluminum 7075-T6 is stiffer: Young's modulus 71 GPa against 3 GPa for Plastic Nylon PA66, so the same part in Aluminum 7075-T6 deflects less under the same load.
Which is lighter for the same job, Aluminum 7075-T6 or Plastic Nylon PA66?
For the same stiffness or strength: Aluminum 7075-T6 is lighter for a stiff rod or tie (tension), stiff beam (bending), stiff panel or plate, strong rod or tie, strong beam; Plastic Nylon PA66 is lighter for a strong panel or plate.
Part that must be
Aluminum 7075-T6
Plastic Nylon PA66
Stiff rod or tie (tension)
lighter
9.55x heavier
Stiff beam (bending)
lighter
1.96x heavier
Stiff panel or plate
lighter
16% heavier
Strong rod or tie
lighter
2.39x heavier
Strong beam
lighter
32% heavier
Strong panel or plate
2% heavier
lighter
For the same stiffness or strength, mass scales with density over stiffness (or strength) raised to a power set by how the part is loaded: 1 for a rod in tension, 1/2 for a beam in bending, 1/3 for a panel (the standard material-selection indices).
Which is more ductile, Aluminum 7075-T6 or Plastic Nylon PA66?
Plastic Nylon PA66 stretches further before it breaks: 30% elongation at break against 11% for Aluminum 7075-T6.
Thermal
Which conducts heat better, Aluminum 7075-T6 or Plastic Nylon PA66?
Aluminum 7075-T6 conducts heat better: 130 W/m·K against 0.33 W/m·K for Plastic Nylon PA66.
Which expands less with temperature?
Aluminum 7075-T6 expands less: 23.4 µm/m·K against 98 µm/m·K for Plastic Nylon PA66.