Thermal conductivity against densityHigher and further left: spreads more heat for its weightThermal expansion against thermal conductivityLower and further right: warps less when heated
Try it on a partA bracket to run stress or thermal on, free in your browser
Sources3 documents: Kaiser Aluminum, Formlabs, U.S. Department of Defense
Aluminum
6061-T6/T651, Kaiser Aluminum typical properties (sheet, coil & plate datasheet); Poisson from MIL-HDBK-5J
SLA Resin Tough 2000
Formlabs Tough 2000 Resin V2 (FLTO2002), TDS Rev. 01 10/06/2025; printed on Form 4 at 100 µm, washed in Form Wash V2 10+5 min in >=99% IPA, post-cured 70 °C for 12 min in Form Cure V2. Orientation not stated.
1
Alloy 6061 Sheet, Coil & Plate Technical DataKaiser Aluminumarchived copyAluminum · Yield strength: typical, 0.2% offset, .500 in dia specimenAluminum · Ultimate tensile strength: typicalAluminum · Elongation at break: typical, in 4D, 0.500 in dia specimenAluminum · Young's modulus (stiffness): typicalAluminum · Density: nominalAluminum · Thermal conductivity: typical, 20 °CAluminum · Thermal expansion: typical, mean 20-100 °CAluminum · Specific heat: typical, at 100 °CAluminum · Melting point: solidus-liquidus
MIL-HDBK-5J, Metallic Materials and Elements for Aerospace Vehicle Structures (2003)U.S. Department of DefenseAluminum · Poisson's ratio: typical (handbook physical constant)
Each number points to the document that states it, with the exact basis. Values without a number are computed from the sourced ones. "Not sourced" means no citable source states it (or only a specification minimum); figures computed from it are left out too.
SLA Resin Tough 2000 is 3D printed: its properties depend on build direction and print settings; these are typical values.
Questions
Mechanical
Is Aluminum stronger than SLA Resin Tough 2000?
Aluminum is stronger: its yield strength is 276 MPa against 40.4 MPa for SLA Resin Tough 2000 (6.83x).
Which is lighter, Aluminum or SLA Resin Tough 2000?
SLA Resin Tough 2000 is lighter: 1,090 kg/m³ against 2,700 kg/m³ for Aluminum.
Which is stiffer, Aluminum or SLA Resin Tough 2000?
Aluminum is stiffer: Young's modulus 68.3 GPa against 1.8 GPa for SLA Resin Tough 2000, so the same part in Aluminum deflects less under the same load.
Which is lighter for the same job, Aluminum or SLA Resin Tough 2000?
For the same stiffness or strength: Aluminum is lighter for a stiff rod or tie (tension), stiff beam (bending), stiff panel or plate, strong rod or tie, strong beam, strong panel or plate.
Part that must be
Aluminum
SLA Resin Tough 2000
Stiff rod or tie (tension)
lighter
15.3x heavier
Stiff beam (bending)
lighter
2.49x heavier
Stiff panel or plate
lighter
36% heavier
Strong rod or tie
lighter
2.76x heavier
Strong beam
lighter
45% heavier
Strong panel or plate
lighter
6% heavier
For the same stiffness or strength, mass scales with density over stiffness (or strength) raised to a power set by how the part is loaded: 1 for a rod in tension, 1/2 for a beam in bending, 1/3 for a panel (the standard material-selection indices).
Which is more ductile, Aluminum or SLA Resin Tough 2000?
SLA Resin Tough 2000 stretches further before it breaks: 79% elongation at break against 17% for Aluminum.
Thermal
Which expands less with temperature?
Aluminum expands less: 23.6 µm/m·K against 134 µm/m·K for SLA Resin Tough 2000.