Thermal conductivity against densityHigher and further left: spreads more heat for its weightThermal expansion against thermal conductivityLower and further right: warps less when heated
Try it on a partA bracket to run stress or thermal on, free in your browser
EOS StainlessSteel 316L Material Data Sheet, M 280 and M 290 (2014)EOS GmbHarchived copyDMLS 316L Stainless Steel · Young's modulus (stiffness): typical, as built, horizontal (XY); EOSINT M280-400W / M290-400W, 316L_Surface 1.0, 20 µm (2014 sheet)
4
EOS StainlessSteel 316L Material Data Sheet, FlexLine, M 290 (2016)EOS GmbHarchived copyDMLS 316L Stainless Steel · Density: part density (ISO 3369, not labelled min or typical), EOS M 290, 40 µm FlexLine
5
Design Manual for Structural Stainless Steel, 4th Edition (P413)Steel Construction Institutearchived copyDMLS 316L Stainless Steel · Poisson's ratio: base material: austenitic stainless steels incl. 1.4404 (316L), design value
6
316/316L Stainless Steel Product Data Bulletin (2021)Cleveland-CliffsDMLS 316L Stainless Steel · Thermal conductivity: base material: wrought 316/316L (Cleveland-Cliffs), at 100 °CDMLS 316L Stainless Steel · Specific heat: base material: wrought 316/316L (Cleveland-Cliffs), 0-100 °C
Each number points to the document that states it, with the exact basis. Values without a number are computed from the sourced ones. "Not sourced" means no citable source states it (or only a specification minimum); figures computed from it are left out too.
DMLS 316L Stainless Steel and Plastic TPU are 3D printed: their properties depend on build direction and print settings; these are typical values.
Questions
Mechanical
Is DMLS 316L Stainless Steel stronger than Plastic TPU?
DMLS 316L Stainless Steel is stronger: its yield strength is 530 MPa against tensile strength 23.7 MPa for Plastic TPU (22.4x).
Which is lighter, DMLS 316L Stainless Steel or Plastic TPU?
Plastic TPU is lighter: 1,220 kg/m³ against 7,900 kg/m³ for DMLS 316L Stainless Steel.
Which is stiffer, DMLS 316L Stainless Steel or Plastic TPU?
DMLS 316L Stainless Steel is stiffer: Young's modulus 185 GPa against 0.067 GPa for Plastic TPU, so the same part in DMLS 316L Stainless Steel deflects less under the same load.
Which is lighter for the same job, DMLS 316L Stainless Steel or Plastic TPU?
For the same stiffness or strength: DMLS 316L Stainless Steel is lighter for a stiff rod or tie (tension), stiff beam (bending), stiff panel or plate, strong rod or tie, strong beam; Plastic TPU is lighter for a strong panel or plate.
Part that must be
DMLS 316L Stainless Steel
Plastic TPU
Stiff rod or tie (tension)
lighter
426x heavier
Stiff beam (bending)
lighter
8.11x heavier
Stiff panel or plate
lighter
2.17x heavier
Strong rod or tie
lighter
3.45x heavier
Strong beam
lighter
23% heavier
Strong panel or plate
37% heavier
lighter
For the same stiffness or strength, mass scales with density over stiffness (or strength) raised to a power set by how the part is loaded: 1 for a rod in tension, 1/2 for a beam in bending, 1/3 for a panel (the standard material-selection indices).