Thermal conductivity against densityHigher and further left: spreads more heat for its weightThermal expansion against thermal conductivityLower and further right: warps less when heated
Try it on a partA bracket to run stress or thermal on, free in your browser
Sources4 documents: Cleveland-Cliffs, BASF Forward AM, National Institute of Standards and Technology, INEOS Styrolution
FDM HIPS
BASF Forward AM (BASF 3D Printing Solutions) Ultrafuse HiPS, TDS v2.2 (13.11.2019), printed specimens, XY 'Flat'. Specimen print settings are not stated; recommended processing on the sheet: nozzle 240-260 °C, bed 100-120 °C, 40-80 mm/s. Product is discontinued (Forward AM product page) but the TDS is still served by Forward AM.
Iron
Cleveland-Cliffs / AK Steel ARMCO Pure Iron Product Data Bulletin (07/2022): Table 1 typical physical properties, Table 2 typical mechanical properties after SRA/recrystallization anneal.
1
ARMCO Pure Iron Product Data Bulletin (2022)Cleveland-Cliffsarchived copyIron · Yield strength: typical (0.2% YS), hot rolled + SRA/recrystallization annealIron · Ultimate tensile strength: typical, SRA/recrystallization annealIron · Elongation at break: typical, gauge 4D0Iron · Young's modulus (stiffness): typical, after SRA/recrystallization annealIron · Density: typicalIron · Thermal conductivity: typical at 20 °CIron · Thermal expansion: mean, 20-399 °CIron · Specific heat: typicalIron · Melting point: typical
Elastic Properties of Metals and Alloys, I. Iron, Nickel, and Iron-Nickel Alloys, J. Phys. Chem. Ref. Data 2 (1973)National Institute of Standards and Technologyarchived copyIron · Poisson's ratio: NIST critically evaluated best value (polycrystalline iron)
Each number points to the document that states it, with the exact basis. Values without a number are computed from the sourced ones. "Not sourced" means no citable source states it (or only a specification minimum); figures computed from it are left out too.
FDM HIPS is 3D printed: its properties depend on build direction and print settings; these are typical values.
Questions
Mechanical
Is FDM HIPS stronger than Iron?
Iron is stronger: its yield strength is 186 MPa against tensile strength 18.4 MPa for FDM HIPS (10.1x).
Which is lighter, FDM HIPS or Iron?
FDM HIPS is lighter: 1,023 kg/m³ against 7,860 kg/m³ for Iron.
Which is stiffer, FDM HIPS or Iron?
Iron is stiffer: Young's modulus 207 GPa against 1.59 GPa for FDM HIPS, so the same part in Iron deflects less under the same load.
Which is lighter for the same job, FDM HIPS or Iron?
For the same stiffness or strength: FDM HIPS is lighter for a stiff panel or plate, strong beam, strong panel or plate; Iron is lighter for a stiff rod or tie (tension), stiff beam (bending), strong rod or tie.
Part that must be
FDM HIPS
Iron
Stiff rod or tie (tension)
17x heavier
lighter
Stiff beam (bending)
49% heavier
lighter
Stiff panel or plate
lighter
1.52x heavier
Strong rod or tie
32% heavier
lighter
Strong beam
lighter
1.64x heavier
Strong panel or plate
lighter
2.42x heavier
For the same stiffness or strength, mass scales with density over stiffness (or strength) raised to a power set by how the part is loaded: 1 for a rod in tension, 1/2 for a beam in bending, 1/3 for a panel (the standard material-selection indices).
Which is more ductile, FDM HIPS or Iron?
Iron stretches further before it breaks: 38% elongation at break against 1.4% for FDM HIPS.
Thermal
Which conducts heat better, FDM HIPS or Iron?
Iron conducts heat better: 73.2 W/m·K against 0.17 W/m·K for FDM HIPS.
Which expands less with temperature?
Iron expands less: 13.7 µm/m·K against 80 µm/m·K for FDM HIPS.