Thermal conductivity against densityHigher and further left: spreads more heat for its weightThermal expansion against thermal conductivityLower and further right: warps less when heated
Try it on a partA bracket to run stress or thermal on, free in your browser
Sources5 documents: Outokumpu, BASF Forward AM, Steel Construction Institute, INEOS Styrolution, Carpenter Technology
FDM HIPS
BASF Forward AM (BASF 3D Printing Solutions) Ultrafuse HiPS, TDS v2.2 (13.11.2019), printed specimens, XY 'Flat'. Specimen print settings are not stated; recommended processing on the sheet: nozzle 240-260 °C, bed 100-120 °C, 40-80 mm/s. Product is discontinued (Forward AM product page) but the TDS is still served by Forward AM.
Stainless Steel 303
1.4305 / UNS S30300, Outokumpu typical values (hot rolled, solution annealed) from 'Steel Grades, Properties and Global Standards'; max service from Carpenter CarTech 303 datasheet
1
Steel Grades, Properties and Global StandardsOutokumpuarchived copyStainless Steel 303 · Yield strength: Outokumpu typical (product P = hot rolled plate, transverse)Stainless Steel 303 · Ultimate tensile strength: Outokumpu typicalStainless Steel 303 · Elongation at break: Outokumpu typical, A5Stainless Steel 303 · Young's modulus (stiffness): at RT (Table 12)Stainless Steel 303 · Density: at RTStainless Steel 303 · Thermal conductivity: at RTStainless Steel 303 · Thermal expansion: mean, 20–100 °CStainless Steel 303 · Specific heat: at RT
Carpenter Stainless Type 303 Data SheetCarpenter Technologyarchived copyStainless Steel 303 · Max service temperature: continuous, scaling limit
Each number points to the document that states it, with the exact basis. Values without a number are computed from the sourced ones. "Not sourced" means no citable source states it (or only a specification minimum); figures computed from it are left out too.
FDM HIPS is 3D printed: its properties depend on build direction and print settings; these are typical values.
Questions
Mechanical
Is FDM HIPS stronger than Stainless Steel 303?
Stainless Steel 303 is stronger: its yield strength is 275 MPa against tensile strength 18.4 MPa for FDM HIPS (14.9x).
Which is lighter, FDM HIPS or Stainless Steel 303?
FDM HIPS is lighter: 1,023 kg/m³ against 7,900 kg/m³ for Stainless Steel 303.
Which is stiffer, FDM HIPS or Stainless Steel 303?
Stainless Steel 303 is stiffer: Young's modulus 200 GPa against 1.59 GPa for FDM HIPS, so the same part in Stainless Steel 303 deflects less under the same load.
Which is lighter for the same job, FDM HIPS or Stainless Steel 303?
For the same stiffness or strength: FDM HIPS is lighter for a stiff panel or plate, strong beam, strong panel or plate; Stainless Steel 303 is lighter for a stiff rod or tie (tension), stiff beam (bending), strong rod or tie.
Part that must be
FDM HIPS
Stainless Steel 303
Stiff rod or tie (tension)
16.3x heavier
lighter
Stiff beam (bending)
45% heavier
lighter
Stiff panel or plate
lighter
1.54x heavier
Strong rod or tie
1.94x heavier
lighter
Strong beam
lighter
27% heavier
Strong panel or plate
lighter
2x heavier
For the same stiffness or strength, mass scales with density over stiffness (or strength) raised to a power set by how the part is loaded: 1 for a rod in tension, 1/2 for a beam in bending, 1/3 for a panel (the standard material-selection indices).
Which is more ductile, FDM HIPS or Stainless Steel 303?
Stainless Steel 303 stretches further before it breaks: 35% elongation at break against 1.4% for FDM HIPS.
Thermal
Which conducts heat better, FDM HIPS or Stainless Steel 303?
Stainless Steel 303 conducts heat better: 15 W/m·K against 0.17 W/m·K for FDM HIPS.
Which expands less with temperature?
Stainless Steel 303 expands less: 16 µm/m·K against 80 µm/m·K for FDM HIPS.