Thermal conductivity against densityHigher and further left: spreads more heat for its weightThermal expansion against thermal conductivityLower and further right: warps less when heated
Try it on a partA bracket to run stress or thermal on, free in your browser
Sources4 documents: Carpenter Technology, BASF Forward AM, U.S. Department of Defense, INEOS Styrolution
FDM HIPS
BASF Forward AM (BASF 3D Printing Solutions) Ultrafuse HiPS, TDS v2.2 (13.11.2019), printed specimens, XY 'Flat'. Specimen print settings are not stated; recommended processing on the sheet: nozzle 240-260 °C, bed 100-120 °C, 40-80 mm/s. Product is discontinued (Forward AM product page) but the TDS is still served by Forward AM.
MIL-HDBK-5J, Metallic Materials and Elements for Aerospace Vehicle Structures (2003)U.S. Department of DefenseSteel AISI 4340 · Young's modulus (stiffness): MIL-HDBK-5J design value (AISI 4340, quenched and tempered)Steel AISI 4340 · Poisson's ratio: MIL-HDBK-5J design value (AISI 4340, quenched and tempered)
Each number points to the document that states it, with the exact basis. Values without a number are computed from the sourced ones. "Not sourced" means no citable source states it (or only a specification minimum); figures computed from it are left out too.
FDM HIPS is 3D printed: its properties depend on build direction and print settings; these are typical values.
Questions
Mechanical
Is FDM HIPS stronger than Steel AISI 4340?
Steel AISI 4340 is stronger: its yield strength is 1,035 MPa against tensile strength 18.4 MPa for FDM HIPS (56.3x).
Which is lighter, FDM HIPS or Steel AISI 4340?
FDM HIPS is lighter: 1,023 kg/m³ against 7,840 kg/m³ for Steel AISI 4340.
Which is stiffer, FDM HIPS or Steel AISI 4340?
Steel AISI 4340 is stiffer: Young's modulus 200 GPa against 1.59 GPa for FDM HIPS, so the same part in Steel AISI 4340 deflects less under the same load.
Which is lighter for the same job, FDM HIPS or Steel AISI 4340?
For the same stiffness or strength: FDM HIPS is lighter for a stiff panel or plate, strong panel or plate; Steel AISI 4340 is lighter for a stiff rod or tie (tension), stiff beam (bending), strong rod or tie, strong beam.
Part that must be
FDM HIPS
Steel AISI 4340
Stiff rod or tie (tension)
16.4x heavier
lighter
Stiff beam (bending)
46% heavier
lighter
Stiff panel or plate
lighter
1.53x heavier
Strong rod or tie
7.34x heavier
lighter
Strong beam
1.92x heavier
lighter
Strong panel or plate
lighter
2% heavier
For the same stiffness or strength, mass scales with density over stiffness (or strength) raised to a power set by how the part is loaded: 1 for a rod in tension, 1/2 for a beam in bending, 1/3 for a panel (the standard material-selection indices).
Which is more ductile, FDM HIPS or Steel AISI 4340?
Steel AISI 4340 stretches further before it breaks: 18% elongation at break against 1.4% for FDM HIPS.
Thermal
Which conducts heat better, FDM HIPS or Steel AISI 4340?
Steel AISI 4340 conducts heat better: 37.5 W/m·K against 0.17 W/m·K for FDM HIPS.
Which expands less with temperature?
Steel AISI 4340 expands less: 11.3 µm/m·K against 80 µm/m·K for FDM HIPS.