Thermal conductivity against densityHigher and further left: spreads more heat for its weightThermal expansion against thermal conductivityLower and further right: warps less when heated
Try it on a partA sample part to run stress or thermal on, free in your browser
Sources2 documents: Pilkington North America, Röhm
Glass
Annealed soda-lime-silica float glass, Pilkington North America Technical Bulletin ATS-129 (04/2025)
Plastic PMMA
Röhm PLEXIGLAS GS 0F00 cast acrylic sheet, typical values at 23 °C / 50 % RH (Röhm Technical Information Ref. No. 211-1)
1
Technical Bulletin ATS-129: Properties of Soda-Lime Silica Float Glass (2025)Pilkington North Americaarchived copyGlass · Ultimate tensile strength: typical mean surface tensile stress at fracture (MOR), 60 s load, weathered, 50% breakage probabilityGlass · Flexural strength: mean MOR (same value as tensile)Glass · Young's modulus (stiffness): typicalGlass · Density: typicalGlass · Poisson's ratio: typicalGlass · Thermal conductivity: typical at 75 FGlass · Thermal expansion: typical, 75-575 FGlass · Specific heat: typical at 75 FGlass · Max service temperature: strain point (ASTM C336) - stress-relaxation onset, not a rated service limit
2
PLEXIGLAS GS and XT Technical Information (Ref. No. 211-1)Röhmarchived copyPlastic PMMA · Ultimate tensile strength: typical, 23 °CPlastic PMMA · Compressive strength: compressive yield stress, typicalPlastic PMMA · Flexural strength: typicalPlastic PMMA · Elongation at break: typicalPlastic PMMA · Young's modulus (stiffness): typical, short-termPlastic PMMA · Density: typicalPlastic PMMA · Poisson's ratio: typicalPlastic PMMA · Thermal conductivity: typicalPlastic PMMA · Thermal expansion: 0-50 °CPlastic PMMA · Specific heat: typicalPlastic PMMA · Max service temperature: max. permanent service temperature
Each number points to the document that states it, with the exact basis. Values without a number are computed from the sourced ones. "Not sourced" means no citable source states it (or only a specification minimum); figures computed from it are left out too.
Questions
Mechanical
Is Glass stronger than Plastic PMMA?
Plastic PMMA is stronger: its tensile strength is 80 MPa against 41 MPa for Glass (1.95x).
Which is lighter, Glass or Plastic PMMA?
Plastic PMMA is lighter: 1,190 kg/m³ against 2,500 kg/m³ for Glass.
Which is stiffer, Glass or Plastic PMMA?
Glass is stiffer: Young's modulus 72 GPa against 3.3 GPa for Plastic PMMA, so the same part in Glass deflects less under the same load.
Which is lighter for the same job, Glass or Plastic PMMA?
For the same stiffness or strength: Glass is lighter for a stiff rod or tie (tension), stiff beam (bending), stiff panel or plate; Plastic PMMA is lighter for a strong rod or tie, strong beam, strong panel or plate.
Part that must be
Glass
Plastic PMMA
Stiff rod or tie (tension)
lighter
10.4x heavier
Stiff beam (bending)
lighter
2.22x heavier
Stiff panel or plate
lighter
33% heavier
Strong rod or tie
4.1x heavier
lighter
Strong beam
3.28x heavier
lighter
Strong panel or plate
2.93x heavier
lighter
For the same stiffness or strength, mass scales with density over stiffness (or strength) raised to a power set by how the part is loaded: 1 for a rod in tension, 1/2 for a beam in bending, 1/3 for a panel (the standard material-selection indices).
Thermal
Which handles higher temperatures, Glass or Plastic PMMA?
Glass does: 511 °C against 80 °C for Plastic PMMA.
Which conducts heat better, Glass or Plastic PMMA?
Glass conducts heat better: 0.937 W/m·K against 0.19 W/m·K for Plastic PMMA.
Which expands less with temperature?
Glass expands less: 8.3 µm/m·K against 70 µm/m·K for Plastic PMMA.