Thermal conductivity against densityHigher and further left: spreads more heat for its weightThermal expansion against thermal conductivityLower and further right: warps less when heated
Try it on a partA sample part to run stress or thermal on, free in your browser
Sources4 documents: Pilkington North America, Formlabs
Glass
Annealed soda-lime-silica float glass, Pilkington North America Technical Bulletin ATS-129 (04/2025)
SLA Resin Standard
Formlabs Clear Resin V5 (FLGPCL05), TDS Rev. 01 March 20, 2024; printed on Form 4 at 100 µm, washed 5 min in >=99% IPA, post-cured 15 min at 60 °C in Form Cure. Orientation not stated.
1
Technical Bulletin ATS-129: Properties of Soda-Lime Silica Float Glass (2025)Pilkington North Americaarchived copyGlass · Ultimate tensile strength: typical mean surface tensile stress at fracture (MOR), 60 s load, weathered, 50% breakage probabilityGlass · Flexural strength: mean MOR (same value as tensile)Glass · Young's modulus (stiffness): typicalGlass · Density: typicalGlass · Poisson's ratio: typicalGlass · Thermal conductivity: typical at 75 FGlass · Thermal expansion: typical, 75-575 FGlass · Specific heat: typical at 75 FGlass · Max service temperature: strain point (ASTM C336) - stress-relaxation onset, not a rated service limit
2
Clear Resin V5 Technical Data Sheet (2024)Formlabsarchived copySLA Resin Standard · Ultimate tensile strength: typicalSLA Resin Standard · Flexural strength: typicalSLA Resin Standard · Elongation at break: typicalSLA Resin Standard · Young's modulus (stiffness): typicalSLA Resin Standard · Max service temperature: HDT 1.8 MPa
3
Clear Resin V5 Technical Data Sheet (web edition)FormlabsSLA Resin Standard · Density: typical, post-cured (same for 5 min ambient and 15 min at 60 °C), ASTM D792
4
Thermal Properties of Selected Formlabs SLA ResinsFormlabsSLA Resin Standard · Thermal conductivity: typical, post-cured, ASTM E1530SLA Resin Standard · Thermal expansion: mean -30 to 140 °C, post-cured (5 min ambient cure), TMA ASTM E831SLA Resin Standard · Specific heat: typical, 25 °C, post-cured (5 min ambient cure), DSC ASTM E1269
Each number points to the document that states it, with the exact basis. Values without a number are computed from the sourced ones. "Not sourced" means no citable source states it (or only a specification minimum); figures computed from it are left out too.
SLA Resin Standard is 3D printed: its properties depend on build direction and print settings; these are typical values.
Questions
Mechanical
Is Glass stronger than SLA Resin Standard?
SLA Resin Standard is stronger: its tensile strength is 60 MPa against 41 MPa for Glass (46%).
Which is lighter, Glass or SLA Resin Standard?
SLA Resin Standard is lighter: 1,210 kg/m³ against 2,500 kg/m³ for Glass.
Which is stiffer, Glass or SLA Resin Standard?
Glass is stiffer: Young's modulus 72 GPa against 2.75 GPa for SLA Resin Standard, so the same part in Glass deflects less under the same load.
Which is lighter for the same job, Glass or SLA Resin Standard?
For the same stiffness or strength: Glass is lighter for a stiff rod or tie (tension), stiff beam (bending), stiff panel or plate; SLA Resin Standard is lighter for a strong rod or tie, strong beam, strong panel or plate.
Part that must be
Glass
SLA Resin Standard
Stiff rod or tie (tension)
lighter
12.7x heavier
Stiff beam (bending)
lighter
2.48x heavier
Stiff panel or plate
lighter
44% heavier
Strong rod or tie
3.02x heavier
lighter
Strong beam
2.66x heavier
lighter
Strong panel or plate
2.5x heavier
lighter
For the same stiffness or strength, mass scales with density over stiffness (or strength) raised to a power set by how the part is loaded: 1 for a rod in tension, 1/2 for a beam in bending, 1/3 for a panel (the standard material-selection indices).
Thermal
Which conducts heat better, Glass or SLA Resin Standard?
Glass conducts heat better: 0.937 W/m·K against 0.54 W/m·K for SLA Resin Standard.
Which expands less with temperature?
Glass expands less: 8.3 µm/m·K against 114 µm/m·K for SLA Resin Standard.