Thermal conductivity against densityHigher and further left: spreads more heat for its weightThermal expansion against thermal conductivityLower and further right: warps less when heated
Try it on a partA sample part to run stress or thermal on, free in your browser
Sources3 documents: Cleveland-Cliffs, Pilkington North America, Steel Construction Institute
Glass
Annealed soda-lime-silica float glass, Pilkington North America Technical Bulletin ATS-129 (04/2025)
Stainless Steel 304
Type 304, annealed flat-rolled (Cleveland-Cliffs 304/304L Product Data Bulletin, May 2021); Poisson's ratio from the Nickel Institute/SCI structural stainless design manual
1
304/304L Stainless Steel Product Data Bulletin (2021)Cleveland-CliffsStainless Steel 304 · Yield strength: typical, annealed, 70 °F (21 °C)Stainless Steel 304 · Ultimate tensile strength: typical, annealed, 70 °F (21 °C)Stainless Steel 304 · Elongation at break: typical, annealed, in 2 in. (50.8 mm)Stainless Steel 304 · Young's modulus (stiffness): typical, in tensionStainless Steel 304 · Density: typicalStainless Steel 304 · Thermal conductivity: at 100 °CStainless Steel 304 · Thermal expansion: mean, 0–100 °CStainless Steel 304 · Specific heat: mean, 0–100 °CStainless Steel 304 · Melting point: melting rangeStainless Steel 304 · Max service temperature: continuous, oxidation (scaling) limit in air
2
Technical Bulletin ATS-129: Properties of Soda-Lime Silica Float Glass (2025)Pilkington North Americaarchived copyGlass · Ultimate tensile strength: typical mean surface tensile stress at fracture (MOR), 60 s load, weathered, 50% breakage probabilityGlass · Flexural strength: mean MOR (same value as tensile)Glass · Young's modulus (stiffness): typicalGlass · Density: typicalGlass · Poisson's ratio: typicalGlass · Thermal conductivity: typical at 75 FGlass · Thermal expansion: typical, 75-575 FGlass · Specific heat: typical at 75 FGlass · Max service temperature: strain point (ASTM C336) - stress-relaxation onset, not a rated service limit
3
Design Manual for Structural Stainless Steel, 4th Edition (P413)Steel Construction Institutearchived copyStainless Steel 304 · Poisson's ratio: design value (structural stainless steels)
Each number points to the document that states it, with the exact basis. Values without a number are computed from the sourced ones. "Not sourced" means no citable source states it (or only a specification minimum); figures computed from it are left out too.
Questions
Mechanical
Is Glass stronger than Stainless Steel 304?
Stainless Steel 304 is stronger: its yield strength is 241 MPa against tensile strength 41 MPa for Glass (5.88x).
Which is lighter, Glass or Stainless Steel 304?
Glass is lighter: 2,500 kg/m³ against 8,030 kg/m³ for Stainless Steel 304.
Which is stiffer, Glass or Stainless Steel 304?
Stainless Steel 304 is stiffer: Young's modulus 193 GPa against 72 GPa for Glass, so the same part in Stainless Steel 304 deflects less under the same load.
Which is lighter for the same job, Glass or Stainless Steel 304?
For the same stiffness or strength: Glass is lighter for a stiff rod or tie (tension), stiff beam (bending), stiff panel or plate, strong panel or plate; Stainless Steel 304 is lighter for a strong rod or tie, strong beam.
Part that must be
Glass
Stainless Steel 304
Stiff rod or tie (tension)
lighter
20% heavier
Stiff beam (bending)
lighter
1.96x heavier
Stiff panel or plate
lighter
2.31x heavier
Strong rod or tie
1.83x heavier
lighter
Strong beam
1% heavier
lighter
Strong panel or plate
lighter
32% heavier
For the same stiffness or strength, mass scales with density over stiffness (or strength) raised to a power set by how the part is loaded: 1 for a rod in tension, 1/2 for a beam in bending, 1/3 for a panel (the standard material-selection indices).
Thermal
Which conducts heat better, Glass or Stainless Steel 304?
Stainless Steel 304 conducts heat better: 16.2 W/m·K against 0.937 W/m·K for Glass.
Which expands less with temperature?
Glass expands less: 8.3 µm/m·K against 16.9 µm/m·K for Stainless Steel 304.