Thermal conductivity against densityHigher and further left: spreads more heat for its weightThermal expansion against thermal conductivityLower and further right: warps less when heated
Try it on a partA bracket to run stress or thermal on, free in your browser
Sources3 documents: Cleveland-Cliffs, Röhm, National Institute of Standards and Technology
Iron
Cleveland-Cliffs / AK Steel ARMCO Pure Iron Product Data Bulletin (07/2022): Table 1 typical physical properties, Table 2 typical mechanical properties after SRA/recrystallization anneal.
Plastic PMMA
Röhm PLEXIGLAS GS 0F00 cast acrylic sheet, typical values at 23 °C / 50 % RH (Röhm Technical Information Ref. No. 211-1)
1
ARMCO Pure Iron Product Data Bulletin (2022)Cleveland-Cliffsarchived copyIron · Yield strength: typical (0.2% YS), hot rolled + SRA/recrystallization annealIron · Ultimate tensile strength: typical, SRA/recrystallization annealIron · Elongation at break: typical, gauge 4D0Iron · Young's modulus (stiffness): typical, after SRA/recrystallization annealIron · Density: typicalIron · Thermal conductivity: typical at 20 °CIron · Thermal expansion: mean, 20-399 °CIron · Specific heat: typicalIron · Melting point: typical
2
PLEXIGLAS GS and XT Technical Information (Ref. No. 211-1)Röhmarchived copyPlastic PMMA · Ultimate tensile strength: typical, 23 °CPlastic PMMA · Compressive strength: compressive yield stress, typicalPlastic PMMA · Flexural strength: typicalPlastic PMMA · Elongation at break: typicalPlastic PMMA · Young's modulus (stiffness): typical, short-termPlastic PMMA · Density: typicalPlastic PMMA · Poisson's ratio: typicalPlastic PMMA · Thermal conductivity: typicalPlastic PMMA · Thermal expansion: 0-50 °CPlastic PMMA · Specific heat: typicalPlastic PMMA · Max service temperature: max. permanent service temperature
3
Elastic Properties of Metals and Alloys, I. Iron, Nickel, and Iron-Nickel Alloys, J. Phys. Chem. Ref. Data 2 (1973)National Institute of Standards and Technologyarchived copyIron · Poisson's ratio: NIST critically evaluated best value (polycrystalline iron)
Each number points to the document that states it, with the exact basis. Values without a number are computed from the sourced ones. "Not sourced" means no citable source states it (or only a specification minimum); figures computed from it are left out too.
Questions
Mechanical
Is Iron stronger than Plastic PMMA?
Iron is stronger: its yield strength is 186 MPa against tensile strength 80 MPa for Plastic PMMA (2.33x).
Which is lighter, Iron or Plastic PMMA?
Plastic PMMA is lighter: 1,190 kg/m³ against 7,860 kg/m³ for Iron.
Which is stiffer, Iron or Plastic PMMA?
Iron is stiffer: Young's modulus 207 GPa against 3.3 GPa for Plastic PMMA, so the same part in Iron deflects less under the same load.
Which is lighter for the same job, Iron or Plastic PMMA?
For the same stiffness or strength: Iron is lighter for a stiff rod or tie (tension), stiff beam (bending); Plastic PMMA is lighter for a stiff panel or plate, strong rod or tie, strong beam, strong panel or plate.
Part that must be
Iron
Plastic PMMA
Stiff rod or tie (tension)
lighter
9.5x heavier
Stiff beam (bending)
lighter
20% heavier
Stiff panel or plate
1.66x heavier
lighter
Strong rod or tie
2.84x heavier
lighter
Strong beam
3.76x heavier
lighter
Strong panel or plate
4.33x heavier
lighter
For the same stiffness or strength, mass scales with density over stiffness (or strength) raised to a power set by how the part is loaded: 1 for a rod in tension, 1/2 for a beam in bending, 1/3 for a panel (the standard material-selection indices).
Which is more ductile, Iron or Plastic PMMA?
Iron stretches further before it breaks: 38% elongation at break against 5.5% for Plastic PMMA.
Thermal
Which conducts heat better, Iron or Plastic PMMA?
Iron conducts heat better: 73.2 W/m·K against 0.19 W/m·K for Plastic PMMA.
Which expands less with temperature?
Iron expands less: 13.7 µm/m·K against 70 µm/m·K for Plastic PMMA.