Thermal conductivity against densityHigher and further left: spreads more heat for its weightThermal expansion against thermal conductivityLower and further right: warps less when heated
Try it on a partA bracket to run stress or thermal on, free in your browser
Sources4 documents: Cleveland-Cliffs, DuPont, National Institute of Standards and Technology
Iron
Cleveland-Cliffs / AK Steel ARMCO Pure Iron Product Data Bulletin (07/2022): Table 1 typical physical properties, Table 2 typical mechanical properties after SRA/recrystallization anneal.
Plastic POM/Acetal
DuPont Delrin 100 acetal homopolymer, Table 2 'Typical Properties of Delrin Acetal Resins' (ASTM methods), Delrin Design Guide Module III hosted on delrin.com
1
ARMCO Pure Iron Product Data Bulletin (2022)Cleveland-Cliffsarchived copyIron · Yield strength: typical (0.2% YS), hot rolled + SRA/recrystallization annealIron · Ultimate tensile strength: typical, SRA/recrystallization annealIron · Elongation at break: typical, gauge 4D0Iron · Young's modulus (stiffness): typical, after SRA/recrystallization annealIron · Density: typicalIron · Thermal conductivity: typical at 20 °CIron · Thermal expansion: mean, 20-399 °CIron · Specific heat: typicalIron · Melting point: typical
Delrin 100 Product Data SheetDuPontPlastic POM/Acetal · Density: typical (DuPont product information for Delrin 100 NC010; 'The data listed here fall within the normal range of product properties')
4
Elastic Properties of Metals and Alloys, I. Iron, Nickel, and Iron-Nickel Alloys, J. Phys. Chem. Ref. Data 2 (1973)National Institute of Standards and Technologyarchived copyIron · Poisson's ratio: NIST critically evaluated best value (polycrystalline iron)
Each number points to the document that states it, with the exact basis. Values without a number are computed from the sourced ones. "Not sourced" means no citable source states it (or only a specification minimum); figures computed from it are left out too.
Questions
Mechanical
Is Iron stronger than Plastic POM/Acetal?
Iron is stronger: its yield strength is 186 MPa against 69 MPa for Plastic POM/Acetal (2.7x).
Which is lighter, Iron or Plastic POM/Acetal?
Plastic POM/Acetal is lighter: 1,420 kg/m³ against 7,860 kg/m³ for Iron.
Which is stiffer, Iron or Plastic POM/Acetal?
Iron is stiffer: Young's modulus 207 GPa against 2.8 GPa for Plastic POM/Acetal, so the same part in Iron deflects less under the same load.
Which is lighter for the same job, Iron or Plastic POM/Acetal?
For the same stiffness or strength: Iron is lighter for a stiff rod or tie (tension), stiff beam (bending); Plastic POM/Acetal is lighter for a stiff panel or plate, strong rod or tie, strong beam, strong panel or plate.
Part that must be
Iron
Plastic POM/Acetal
Stiff rod or tie (tension)
lighter
13.4x heavier
Stiff beam (bending)
lighter
1.55x heavier
Stiff panel or plate
32% heavier
lighter
Strong rod or tie
2.05x heavier
lighter
Strong beam
2.86x heavier
lighter
Strong panel or plate
3.37x heavier
lighter
For the same stiffness or strength, mass scales with density over stiffness (or strength) raised to a power set by how the part is loaded: 1 for a rod in tension, 1/2 for a beam in bending, 1/3 for a panel (the standard material-selection indices).
Which is more ductile, Iron or Plastic POM/Acetal?
Plastic POM/Acetal stretches further before it breaks: 75% elongation at break against 38% for Iron.
Thermal
Which conducts heat better, Iron or Plastic POM/Acetal?
Iron conducts heat better: 73.2 W/m·K against 0.4 W/m·K for Plastic POM/Acetal.
Which expands less with temperature?
Iron expands less: 13.7 µm/m·K against 122 µm/m·K for Plastic POM/Acetal.