Thermal conductivity against densityHigher and further left: spreads more heat for its weightThermal expansion against thermal conductivityLower and further right: warps less when heated
Try it on a partA bracket to run stress or thermal on, free in your browser
Sources4 documents: Cleveland-Cliffs, Niagara LaSalle, Ovako, National Institute of Standards and Technology
Iron
Cleveland-Cliffs / AK Steel ARMCO Pure Iron Product Data Bulletin (07/2022): Table 1 typical physical properties, Table 2 typical mechanical properties after SRA/recrystallization anneal.
Steel AISI 1045
AISI 1045 cold drawn bar (Niagara LaSalle) for mechanical; Ovako C45 (lists 'SAE 1045' as a similar designation) for physical constants
1
ARMCO Pure Iron Product Data Bulletin (2022)Cleveland-Cliffsarchived copyIron · Yield strength: typical (0.2% YS), hot rolled + SRA/recrystallization annealIron · Ultimate tensile strength: typical, SRA/recrystallization annealIron · Elongation at break: typical, gauge 4D0Iron · Young's modulus (stiffness): typical, after SRA/recrystallization annealIron · Density: typicalIron · Thermal conductivity: typical at 20 °CIron · Thermal expansion: mean, 20-399 °CIron · Specific heat: typicalIron · Melting point: typical
Elastic Properties of Metals and Alloys, I. Iron, Nickel, and Iron-Nickel Alloys, J. Phys. Chem. Ref. Data 2 (1973)National Institute of Standards and Technologyarchived copyIron · Poisson's ratio: NIST critically evaluated best value (polycrystalline iron)
Each number points to the document that states it, with the exact basis. Values without a number are computed from the sourced ones. "Not sourced" means no citable source states it (or only a specification minimum); figures computed from it are left out too.
Questions
Mechanical
Is Iron stronger than Steel AISI 1045?
Steel AISI 1045 is stronger: its yield strength is 531 MPa against 186 MPa for Iron (2.85x).
Which is lighter, Iron or Steel AISI 1045?
Steel AISI 1045 is lighter: 7,800 kg/m³ against 7,860 kg/m³ for Iron.
Which is stiffer, Iron or Steel AISI 1045?
Steel AISI 1045 is stiffer: Young's modulus 210 GPa against 207 GPa for Iron, so the same part in Steel AISI 1045 deflects less under the same load.
Which is lighter for the same job, Iron or Steel AISI 1045?
For the same stiffness or strength: Steel AISI 1045 is lighter for a stiff rod or tie (tension), stiff beam (bending), stiff panel or plate, strong rod or tie, strong beam, strong panel or plate.
Part that must be
Iron
Steel AISI 1045
Stiff rod or tie (tension)
2% heavier
lighter
Stiff beam (bending)
1% heavier
lighter
Stiff panel or plate
1% heavier
lighter
Strong rod or tie
2.88x heavier
lighter
Strong beam
2.03x heavier
lighter
Strong panel or plate
1.7x heavier
lighter
For the same stiffness or strength, mass scales with density over stiffness (or strength) raised to a power set by how the part is loaded: 1 for a rod in tension, 1/2 for a beam in bending, 1/3 for a panel (the standard material-selection indices).
Which is more ductile, Iron or Steel AISI 1045?
Iron stretches further before it breaks: 38% elongation at break against 12% for Steel AISI 1045.
Thermal
Which conducts heat better, Iron or Steel AISI 1045?
Iron conducts heat better: 73.2 W/m·K against 42.5 W/m·K for Steel AISI 1045.
Which expands less with temperature?
Steel AISI 1045 expands less: 12 µm/m·K against 13.7 µm/m·K for Iron.