Thermal conductivity against densityHigher and further left: spreads more heat for its weightThermal expansion against thermal conductivityLower and further right: warps less when heated
Try it on a partA bracket to run stress or thermal on, free in your browser
Sources6 documents: UltiMaker, Outokumpu, Covestro, Steel Construction Institute, INEOS Styrolution, Carpenter Technology
Plastic ABS
Ultimaker ABS, 3D-printed specimens, XY (flat); Ultimaker S5 Pro, engineering intent profile, 0.15 mm layer height, AA 0.4 print core, 100% infill, Cura 4.9, printed one-at-a-time, conditioned >=24 h at room temperature. TDS v5.00, April 20, 2022.
Stainless Steel 303
1.4305 / UNS S30300, Outokumpu typical values (hot rolled, solution annealed) from 'Steel Grades, Properties and Global Standards'; max service from Carpenter CarTech 303 datasheet
Steel Grades, Properties and Global StandardsOutokumpuarchived copyStainless Steel 303 · Yield strength: Outokumpu typical (product P = hot rolled plate, transverse)Stainless Steel 303 · Ultimate tensile strength: Outokumpu typicalStainless Steel 303 · Elongation at break: Outokumpu typical, A5Stainless Steel 303 · Young's modulus (stiffness): at RT (Table 12)Stainless Steel 303 · Density: at RTStainless Steel 303 · Thermal conductivity: at RTStainless Steel 303 · Thermal expansion: mean, 20–100 °CStainless Steel 303 · Specific heat: at RT
3
Engineering Polymers Part and Mold Design: Thermoplastics, A Design GuideCovestroarchived copyPlastic ABS · Poisson's ratio: base material: ABS family typical (Covestro Part and Mold Design guide, Table 3-1)
4
Design Manual for Structural Stainless Steel, 4th Edition (P413)Steel Construction Institutearchived copyStainless Steel 303 · Poisson's ratio: design value (structural stainless steels)
5
Terluran GP-22 (ABS) Product Data SheetINEOS StyrolutionPlastic ABS · Thermal conductivity: base material: INEOS Styrolution Terluran GP-22 injection-molding ABS, typicalPlastic ABS · Thermal expansion: base material: INEOS Styrolution Terluran GP-22 injection-molding ABS, range
6
Carpenter Stainless Type 303 Data SheetCarpenter Technologyarchived copyStainless Steel 303 · Max service temperature: continuous, scaling limit
Each number points to the document that states it, with the exact basis. Values without a number are computed from the sourced ones. "Not sourced" means no citable source states it (or only a specification minimum); figures computed from it are left out too.
Plastic ABS is 3D printed: its properties depend on build direction and print settings; these are typical values.
Questions
Mechanical
Is Plastic ABS stronger than Stainless Steel 303?
Stainless Steel 303 is stronger: its yield strength is 275 MPa against 38.1 MPa for Plastic ABS (7.22x).
Which is lighter, Plastic ABS or Stainless Steel 303?
Plastic ABS is lighter: 1,100 kg/m³ against 7,900 kg/m³ for Stainless Steel 303.
Which is stiffer, Plastic ABS or Stainless Steel 303?
Stainless Steel 303 is stiffer: Young's modulus 200 GPa against 1.96 GPa for Plastic ABS, so the same part in Stainless Steel 303 deflects less under the same load.
Which is lighter for the same job, Plastic ABS or Stainless Steel 303?
For the same stiffness or strength: Plastic ABS is lighter for a stiff panel or plate, strong beam, strong panel or plate; Stainless Steel 303 is lighter for a stiff rod or tie (tension), stiff beam (bending).
Part that must be
Plastic ABS
Stainless Steel 303
Stiff rod or tie (tension)
14.2x heavier
lighter
Stiff beam (bending)
41% heavier
lighter
Stiff panel or plate
lighter
1.54x heavier
Strong rod or tie
about equal
about equal
Strong beam
lighter
1.92x heavier
Strong panel or plate
lighter
2.67x heavier
For the same stiffness or strength, mass scales with density over stiffness (or strength) raised to a power set by how the part is loaded: 1 for a rod in tension, 1/2 for a beam in bending, 1/3 for a panel (the standard material-selection indices).
Which is more ductile, Plastic ABS or Stainless Steel 303?
Stainless Steel 303 stretches further before it breaks: 35% elongation at break against 4.6% for Plastic ABS.
Thermal
Which conducts heat better, Plastic ABS or Stainless Steel 303?
Stainless Steel 303 conducts heat better: 15 W/m·K against 0.17 W/m·K for Plastic ABS.
Which expands less with temperature?
Stainless Steel 303 expands less: 16 µm/m·K against 95 µm/m·K for Plastic ABS.