Thermal conductivity against densityHigher and further left: spreads more heat for its weightThermal expansion against thermal conductivityLower and further right: warps less when heated
Try it on a partA bracket to run stress or thermal on, free in your browser
TIMETAL 6-4 PropertiesTIMETarchived copyTitanium · Yield strength: typical, plate (>0.187 in), annealed, 0.2% offsetTitanium · Ultimate tensile strength: typical, plate, annealedTitanium · Elongation at break: typical, in 2 in., plate annealedTitanium · Density: nominalTitanium · Poisson's ratio: mean of TIMET measurementsTitanium · Melting point: melting rangeTitanium · Max service temperature: upper recommended use temperature
3
TIMETAL 6-4 Data SheetTIMETarchived copyTitanium · Young's modulus (stiffness): typical range, 20 °CTitanium · Thermal conductivity: typical, 20 °C, mill annealedTitanium · Thermal expansion: typical, mean 0-100 °CTitanium · Specific heat: typical, 20 °C
4
Engineering Polymers Part and Mold Design: Thermoplastics, A Design GuideCovestroarchived copyPlastic ABS · Poisson's ratio: base material: ABS family typical (Covestro Part and Mold Design guide, Table 3-1)
5
Terluran GP-22 (ABS) Product Data SheetINEOS StyrolutionPlastic ABS · Thermal conductivity: base material: INEOS Styrolution Terluran GP-22 injection-molding ABS, typicalPlastic ABS · Thermal expansion: base material: INEOS Styrolution Terluran GP-22 injection-molding ABS, range
Each number points to the document that states it, with the exact basis. Values without a number are computed from the sourced ones. "Not sourced" means no citable source states it (or only a specification minimum); figures computed from it are left out too.
Plastic ABS is 3D printed: its properties depend on build direction and print settings; these are typical values.
Questions
Mechanical
Is Plastic ABS stronger than Titanium?
Titanium is stronger: its yield strength is 885 MPa against 38.1 MPa for Plastic ABS (23.2x).
Which is lighter, Plastic ABS or Titanium?
Plastic ABS is lighter: 1,100 kg/m³ against 4,430 kg/m³ for Titanium.
Which is stiffer, Plastic ABS or Titanium?
Titanium is stiffer: Young's modulus 115 GPa against 1.96 GPa for Plastic ABS, so the same part in Titanium deflects less under the same load.
Which is lighter for the same job, Plastic ABS or Titanium?
For the same stiffness or strength: Plastic ABS is lighter for a stiff panel or plate; Titanium is lighter for a stiff rod or tie (tension), stiff beam (bending), strong rod or tie, strong beam, strong panel or plate.
Part that must be
Plastic ABS
Titanium
Stiff rod or tie (tension)
14.5x heavier
lighter
Stiff beam (bending)
1.9x heavier
lighter
Stiff panel or plate
lighter
4% heavier
Strong rod or tie
5.77x heavier
lighter
Strong beam
2.02x heavier
lighter
Strong panel or plate
20% heavier
lighter
For the same stiffness or strength, mass scales with density over stiffness (or strength) raised to a power set by how the part is loaded: 1 for a rod in tension, 1/2 for a beam in bending, 1/3 for a panel (the standard material-selection indices).
Which is more ductile, Plastic ABS or Titanium?
Titanium stretches further before it breaks: 16% elongation at break against 4.6% for Plastic ABS.
Thermal
Which conducts heat better, Plastic ABS or Titanium?
Titanium conducts heat better: 6.6 W/m·K against 0.17 W/m·K for Plastic ABS.
Which expands less with temperature?
Titanium expands less: 9 µm/m·K against 95 µm/m·K for Plastic ABS.