Thermal conductivity against densityHigher and further left: spreads more heat for its weightThermal expansion against thermal conductivityLower and further right: warps less when heated
Try it on a partA bracket to run stress or thermal on, free in your browser
Wood Handbook (FPL-GTR-282), Chapter 5: Mechanical Properties of WoodUSDA Forest Products LaboratoryWood · Ultimate tensile strength: modulus of rupture (no direct tensile value)Wood · Compressive strength: compression parallel to grain (maximum crushing strength), 12% MCWood · Flexural strength: modulus of rupture (static bending), 12% MCWood · Young's modulus (stiffness): bending MOE, parallel to grainWood · Poisson's ratio: mu_LR (red oak group, ~12% MC)
3
Technical Note 218: Weights of Various Woods Grown in the United States (1953)USDA Forest Products LaboratoryWood · Density: average weight of clear wood at 8% and 15% moisture content
4
Engineering Polymers Part and Mold Design: Thermoplastics, A Design GuideCovestroarchived copyPlastic ABS · Poisson's ratio: base material: ABS family typical (Covestro Part and Mold Design guide, Table 3-1)
5
Terluran GP-22 (ABS) Product Data SheetINEOS StyrolutionPlastic ABS · Thermal conductivity: base material: INEOS Styrolution Terluran GP-22 injection-molding ABS, typicalPlastic ABS · Thermal expansion: base material: INEOS Styrolution Terluran GP-22 injection-molding ABS, range
6
Wood Handbook (FPL-GTR-282), Chapter 4: Moisture Relations and Physical Properties of WoodUSDA Forest Products LaboratoryWood · Thermal conductivity: across grain, 12% MC (Table 4-7, approximate)Wood · Thermal expansion: parallel to grain, ovendry wood, range across speciesWood · Specific heat: solid wood (all species), 12% MC, 27 C
Each number points to the document that states it, with the exact basis. Values without a number are computed from the sourced ones. "Not sourced" means no citable source states it (or only a specification minimum); figures computed from it are left out too.
Plastic ABS is 3D printed: its properties depend on build direction and print settings; these are typical values.
Questions
Mechanical
Is Plastic ABS stronger than Wood?
Wood is stronger: its tensile strength is 99 MPa against yield strength 38.1 MPa for Plastic ABS (2.6x).
Which is lighter, Plastic ABS or Wood?
Wood is lighter: 692 kg/m³ against 1,100 kg/m³ for Plastic ABS.
Which is stiffer, Plastic ABS or Wood?
Wood is stiffer: Young's modulus 12.5 GPa against 1.96 GPa for Plastic ABS, so the same part in Wood deflects less under the same load.
Which is lighter for the same job, Plastic ABS or Wood?
For the same stiffness or strength: Wood is lighter for a stiff rod or tie (tension), stiff beam (bending), stiff panel or plate, strong rod or tie, strong beam, strong panel or plate.
Part that must be
Plastic ABS
Wood
Stiff rod or tie (tension)
10.1x heavier
lighter
Stiff beam (bending)
4.02x heavier
lighter
Stiff panel or plate
2.95x heavier
lighter
Strong rod or tie
4.13x heavier
lighter
Strong beam
3.01x heavier
lighter
Strong panel or plate
2.56x heavier
lighter
For the same stiffness or strength, mass scales with density over stiffness (or strength) raised to a power set by how the part is loaded: 1 for a rod in tension, 1/2 for a beam in bending, 1/3 for a panel (the standard material-selection indices).
Thermal
Which conducts heat better, Plastic ABS or Wood?
Wood conducts heat better: 0.18 W/m·K against 0.17 W/m·K for Plastic ABS.
Which expands less with temperature?
Wood expands less: 3.8 µm/m·K against 95 µm/m·K for Plastic ABS.