Thermal conductivity against densityHigher and further left: spreads more heat for its weightThermal expansion against thermal conductivityLower and further right: warps less when heated
Try it on a partA bracket to run stress or thermal on, free in your browser
TIMETAL 6-4 PropertiesTIMETarchived copyTitanium · Yield strength: typical, plate (>0.187 in), annealed, 0.2% offsetTitanium · Ultimate tensile strength: typical, plate, annealedTitanium · Elongation at break: typical, in 2 in., plate annealedTitanium · Density: nominalTitanium · Poisson's ratio: mean of TIMET measurementsTitanium · Melting point: melting rangeTitanium · Max service temperature: upper recommended use temperature
3
TIMETAL 6-4 Data SheetTIMETarchived copyTitanium · Young's modulus (stiffness): typical range, 20 °CTitanium · Thermal conductivity: typical, 20 °C, mill annealedTitanium · Thermal expansion: typical, mean 0-100 °CTitanium · Specific heat: typical, 20 °C
4
Engineering Polymers Part and Mold Design: Thermoplastics, A Design GuideCovestroPlastic Nylon PA6 · Poisson's ratio: base material: unfilled polyamide (PA), conditioned, maker design-guide family value (Covestro Table 3-1)
Each number points to the document that states it, with the exact basis. Values without a number are computed from the sourced ones. "Not sourced" means no citable source states it (or only a specification minimum); figures computed from it are left out too.
Questions
Mechanical
Is Plastic Nylon PA6 stronger than Titanium?
Titanium is stronger: its yield strength is 885 MPa against 90 MPa for Plastic Nylon PA6 (9.83x).
Which is lighter, Plastic Nylon PA6 or Titanium?
Plastic Nylon PA6 is lighter: 1,130 kg/m³ against 4,430 kg/m³ for Titanium.
Which is stiffer, Plastic Nylon PA6 or Titanium?
Titanium is stiffer: Young's modulus 115 GPa against 3.5 GPa for Plastic Nylon PA6, so the same part in Titanium deflects less under the same load.
Which is lighter for the same job, Plastic Nylon PA6 or Titanium?
For the same stiffness or strength: Plastic Nylon PA6 is lighter for a stiff panel or plate, strong panel or plate; Titanium is lighter for a stiff rod or tie (tension), stiff beam (bending), strong rod or tie, strong beam.
Part that must be
Plastic Nylon PA6
Titanium
Stiff rod or tie (tension)
8.34x heavier
lighter
Stiff beam (bending)
46% heavier
lighter
Stiff panel or plate
lighter
23% heavier
Strong rod or tie
2.51x heavier
lighter
Strong beam
17% heavier
lighter
Strong panel or plate
lighter
25% heavier
For the same stiffness or strength, mass scales with density over stiffness (or strength) raised to a power set by how the part is loaded: 1 for a rod in tension, 1/2 for a beam in bending, 1/3 for a panel (the standard material-selection indices).
Which is more ductile, Plastic Nylon PA6 or Titanium?
Titanium stretches further before it breaks: 16% elongation at break against 10% for Plastic Nylon PA6.
Thermal
Which conducts heat better, Plastic Nylon PA6 or Titanium?
Titanium conducts heat better: 6.6 W/m·K against 0.33 W/m·K for Plastic Nylon PA6.
Which expands less with temperature?
Titanium expands less: 9 µm/m·K against 102 µm/m·K for Plastic Nylon PA6.