Thermal conductivity against densityHigher and further left: spreads more heat for its weightThermal expansion against thermal conductivityLower and further right: warps less when heated
Try it on a partA bracket to run stress or thermal on, free in your browser
Updating Standard Shape Material Properties Database for Design and ReliabilityAmerican Institute of Steel Constructionarchived copySteel A992 · Yield strength: typical: mean of 20,295 A992 flange mill-test coupons (1998 SSPC survey), as reported by AISCSteel A992 · Ultimate tensile strength: typical: mean of 20,295 A992 flange mill-test coupons (1998 SSPC survey)Steel A992 · Elongation at break: typical: mean of 24,847 A992 mill-test elongations, web and flange (1998 SSPC mill data), as reported by AISC
3
ANSI/AISC 360-16 Specification for Structural Steel Buildings, with CommentaryAmerican Institute of Steel Constructionarchived copySteel A992 · Young's modulus (stiffness): design value (AISC 360-16)Steel A992 · Poisson's ratio: design value (AISC 360-16 Commentary)
4
Environmental Product Declaration: Structural Steel Sections and Merchant Bars (2023)bauforumstahl (ArcelorMittal)archived copySteel A992 · Density: nominal (constructional data)Steel A992 · Thermal conductivity: nominal at 20 °CSteel A992 · Thermal expansion: nominal (constructional data, no temperature range stated)
5
Engineering Properties of Ingeo BiopolymerNatureWorksarchived copyPlastic PLA · Thermal conductivity: base material: NatureWorks Ingeo biopolymer, amorphous sheet, 25 °CPlastic PLA · Specific heat: base material: NatureWorks Ingeo biopolymer, amorphous sheet, 25 °C
6
S275JR Steel GradeOvakoSteel A992 · Specific heat: base material: EN S275JR unalloyed structural steel (the EN counterpart of A36), typical, 50/100 °C
Each number points to the document that states it, with the exact basis. Values without a number are computed from the sourced ones. "Not sourced" means no citable source states it (or only a specification minimum); figures computed from it are left out too.
Plastic PLA is 3D printed: its properties depend on build direction and print settings; these are typical values.
Questions
Mechanical
Is Plastic PLA stronger than Steel A992?
Steel A992 is stronger: its yield strength is 385 MPa against 52.5 MPa for Plastic PLA (7.33x).
Which is lighter, Plastic PLA or Steel A992?
Plastic PLA is lighter: 1,240 kg/m³ against 7,850 kg/m³ for Steel A992.
Which is stiffer, Plastic PLA or Steel A992?
Steel A992 is stiffer: Young's modulus 200 GPa against 3.25 GPa for Plastic PLA, so the same part in Steel A992 deflects less under the same load.
Which is lighter for the same job, Plastic PLA or Steel A992?
For the same stiffness or strength: Plastic PLA is lighter for a stiff panel or plate, strong beam, strong panel or plate; Steel A992 is lighter for a stiff rod or tie (tension), stiff beam (bending), strong rod or tie.
Part that must be
Plastic PLA
Steel A992
Stiff rod or tie (tension)
9.72x heavier
lighter
Stiff beam (bending)
24% heavier
lighter
Stiff panel or plate
lighter
1.6x heavier
Strong rod or tie
16% heavier
lighter
Strong beam
lighter
1.68x heavier
Strong panel or plate
lighter
2.34x heavier
For the same stiffness or strength, mass scales with density over stiffness (or strength) raised to a power set by how the part is loaded: 1 for a rod in tension, 1/2 for a beam in bending, 1/3 for a panel (the standard material-selection indices).
Which is more ductile, Plastic PLA or Steel A992?
Steel A992 stretches further before it breaks: 24.2% elongation at break against 7.8% for Plastic PLA.
Thermal
Which conducts heat better, Plastic PLA or Steel A992?
Steel A992 conducts heat better: 48 W/m·K against 0.13 W/m·K for Plastic PLA.