Thermal conductivity against densityHigher and further left: spreads more heat for its weightThermal expansion against thermal conductivityLower and further right: warps less when heated
Try it on a partA bracket to run stress or thermal on, free in your browser
MIL-HDBK-5J, Metallic Materials and Elements for Aerospace Vehicle Structures (2003)U.S. Department of DefenseSteel AISI 1018 · Young's modulus (stiffness): base material: AISI 1025 plain carbon steel (MIL-HDBK-5J design value; ASTM A108 bar is the cold-finished carbon-steel bar spec that also covers 1018)Steel AISI 1018 · Density: base material: AISI 1025 plain carbon steel (MIL-HDBK-5J design value; ASTM A108 bar is the cold-finished carbon-steel bar spec that also covers 1018)Steel AISI 1018 · Poisson's ratio: base material: AISI 1025 plain carbon steel (MIL-HDBK-5J design value; ASTM A108 bar is the cold-finished carbon-steel bar spec that also covers 1018)Steel AISI 1018 · Thermal conductivity: base material: AISI 1025 plain carbon steel (MIL-HDBK-5J design value; ASTM A108 bar is the cold-finished carbon-steel bar spec that also covers 1018)Steel AISI 1018 · Specific heat: base material: AISI 1025 plain carbon steel (MIL-HDBK-5J design value; ASTM A108 bar is the cold-finished carbon-steel bar spec that also covers 1018)
4
Zinc Die Casting Properties Guide (2012)Eastern AlloysZinc Zamak 3 · Poisson's ratio: typical, Zamak 3 hot-chamber die cast
5
S275JR Steel GradeOvakoSteel AISI 1018 · Thermal expansion: base material: unalloyed carbon steel, Ovako family table (S275JR, 'none alloyed structural steels', C <= 0.21%); mean 20-300 °C
Each number points to the document that states it, with the exact basis. Values without a number are computed from the sourced ones. "Not sourced" means no citable source states it (or only a specification minimum); figures computed from it are left out too.
Questions
Mechanical
Is Steel AISI 1018 stronger than Zinc Zamak 3?
Steel AISI 1018 is stronger: its yield strength is 372 MPa against 221 MPa for Zinc Zamak 3 (1.68x).
Which is lighter, Steel AISI 1018 or Zinc Zamak 3?
Zinc Zamak 3 is lighter: 6,600 kg/m³ against 7,861 kg/m³ for Steel AISI 1018.
Which is stiffer, Steel AISI 1018 or Zinc Zamak 3?
Steel AISI 1018 is stiffer: Young's modulus 200 GPa against 85.5 GPa for Zinc Zamak 3, so the same part in Steel AISI 1018 deflects less under the same load.
Which is lighter for the same job, Steel AISI 1018 or Zinc Zamak 3?
For the same stiffness or strength: Steel AISI 1018 is lighter for a stiff rod or tie (tension), stiff beam (bending), stiff panel or plate, strong rod or tie, strong beam, strong panel or plate.
Part that must be
Steel AISI 1018
Zinc Zamak 3
Stiff rod or tie (tension)
lighter
1.96x heavier
Stiff beam (bending)
lighter
28% heavier
Stiff panel or plate
lighter
11% heavier
Strong rod or tie
lighter
41% heavier
Strong beam
lighter
19% heavier
Strong panel or plate
lighter
9% heavier
For the same stiffness or strength, mass scales with density over stiffness (or strength) raised to a power set by how the part is loaded: 1 for a rod in tension, 1/2 for a beam in bending, 1/3 for a panel (the standard material-selection indices).
Which is more ductile, Steel AISI 1018 or Zinc Zamak 3?
Steel AISI 1018 stretches further before it breaks: 15% elongation at break against 10% for Zinc Zamak 3.
Thermal
Which conducts heat better, Steel AISI 1018 or Zinc Zamak 3?
Zinc Zamak 3 conducts heat better: 113 W/m·K against 51.9 W/m·K for Steel AISI 1018.
Which expands less with temperature?
Steel AISI 1018 expands less: 12 µm/m·K against 27.4 µm/m·K for Zinc Zamak 3.