Thermal conductivity against densityHigher and further left: spreads more heat for its weightThermal expansion against thermal conductivityLower and further right: warps less when heated
Try it on a partA sample part to run stress or thermal on, free in your browser
Sources3 documents: Kaiser Aluminum, Sumitomo Chemical, Hydro
Aluminum 1100-O
1100-O (annealed) commercially pure aluminium, Kaiser Aluminum Tube & Pipe Alloy 1100 Technical Data (Rev. 05/06), typical properties; specific heat from Hydro EN AW-1050A (99.5% Al) extruded-products datasheet (10/2018).
Plastic LCP GF30
Sumitomo Chemical SUMIKASUPER LCP E6006L (30% glass fibre; high strength, low shrinkage); SUMIKASUPER LCP Technical Note, Version 04 / Nov. 2023, typical values.
1
Alloy 1100 Tube & Pipe Technical Data, Rev. 05/06Kaiser Aluminumarchived copyAluminum 1100-O · Yield strength: typical, O, 0.0625 in specimenAluminum 1100-O · Ultimate tensile strength: typical, OAluminum 1100-O · Elongation at break: typical, O, in 4DAluminum 1100-O · Young's modulus (stiffness): typicalAluminum 1100-O · Density: nominal, 20 °CAluminum 1100-O · Thermal conductivity: typical, O, 20 °CAluminum 1100-O · Thermal expansion: typical, mean 20-100 °CAluminum 1100-O · Melting point: melting range
2
SUMIKASUPER LCP Technical Note, Version 04 (2023)Sumitomo Chemicalarchived copyPlastic LCP GF30 · Ultimate tensile strength: tensile strength (ISO 527)Plastic LCP GF30 · Flexural strength: typical (ISO 178)Plastic LCP GF30 · Elongation at break: tensile elongation (ISO 527)Plastic LCP GF30 · Young's modulus (stiffness): tensile modulus (ISO 527)Plastic LCP GF30 · Density: typicalPlastic LCP GF30 · Thermal conductivity: hot disk (ISO 22007-2), temperature not statedPlastic LCP GF30 · Thermal expansion: flow direction (MD), mean 50-150 °CPlastic LCP GF30 · Specific heat: ASTM E1269, temperature not statedPlastic LCP GF30 · Max service temperature: HDT 1.8 MPa (ISO 75)
3
Technical Datasheet, Extruded Products: Alloy EN AW-1050AHydroAluminum 1100-O · Specific heat: base material: commercially pure aluminium EN AW-1050A (Hydro), 20 °C
Each number points to the document that states it, with the exact basis. Values without a number are computed from the sourced ones. "Not sourced" means no citable source states it (or only a specification minimum); figures computed from it are left out too.
Questions
Mechanical
Is Aluminum 1100-O stronger than Plastic LCP GF30?
Plastic LCP GF30 is stronger: its tensile strength is 115 MPa against yield strength 35 MPa for Aluminum 1100-O (3.29x).
Which is lighter, Aluminum 1100-O or Plastic LCP GF30?
Plastic LCP GF30 is lighter: 1,610 kg/m³ against 2,710 kg/m³ for Aluminum 1100-O.
Which is stiffer, Aluminum 1100-O or Plastic LCP GF30?
Aluminum 1100-O is stiffer: Young's modulus 69 GPa against 11.5 GPa for Plastic LCP GF30, so the same part in Aluminum 1100-O deflects less under the same load.
Which is lighter for the same job, Aluminum 1100-O or Plastic LCP GF30?
For the same stiffness or strength: Aluminum 1100-O is lighter for a stiff rod or tie (tension), stiff beam (bending), stiff panel or plate; Plastic LCP GF30 is lighter for a strong rod or tie, strong beam, strong panel or plate.
Part that must be
Aluminum 1100-O
Plastic LCP GF30
Stiff rod or tie (tension)
lighter
3.56x heavier
Stiff beam (bending)
lighter
46% heavier
Stiff panel or plate
lighter
8% heavier
Strong rod or tie
5.53x heavier
lighter
Strong beam
3.72x heavier
lighter
Strong panel or plate
3.05x heavier
lighter
For the same stiffness or strength, mass scales with density over stiffness (or strength) raised to a power set by how the part is loaded: 1 for a rod in tension, 1/2 for a beam in bending, 1/3 for a panel (the standard material-selection indices).
Which is more ductile, Aluminum 1100-O or Plastic LCP GF30?
Aluminum 1100-O stretches further before it breaks: 35% elongation at break against 1.5% for Plastic LCP GF30.
Thermal
Which conducts heat better, Aluminum 1100-O or Plastic LCP GF30?
Aluminum 1100-O conducts heat better: 222 W/m·K against 0.5 W/m·K for Plastic LCP GF30.
Which expands less with temperature?
Plastic LCP GF30 expands less: 20 µm/m·K against 23.6 µm/m·K for Aluminum 1100-O.