Thermal conductivity against densityHigher and further left: spreads more heat for its weightThermal expansion against thermal conductivityLower and further right: warps less when heated
Try it on a partA sample part to run stress or thermal on, free in your browser
Sources3 documents: Kaiser Aluminum, Formlabs, Hydro
Aluminum 1100-O
1100-O (annealed) commercially pure aluminium, Kaiser Aluminum Tube & Pipe Alloy 1100 Technical Data (Rev. 05/06), typical properties; specific heat from Hydro EN AW-1050A (99.5% Al) extruded-products datasheet (10/2018).
SLA Resin Tough 2000
Formlabs Tough 2000 Resin V2 (FLTO2002), TDS Rev. 01 10/06/2025; printed on Form 4 at 100 µm, washed in Form Wash V2 10+5 min in >=99% IPA, post-cured 70 °C for 12 min in Form Cure V2. Orientation not stated.
1
Alloy 1100 Tube & Pipe Technical Data, Rev. 05/06Kaiser Aluminumarchived copyAluminum 1100-O · Yield strength: typical, O, 0.0625 in specimenAluminum 1100-O · Ultimate tensile strength: typical, OAluminum 1100-O · Elongation at break: typical, O, in 4DAluminum 1100-O · Young's modulus (stiffness): typicalAluminum 1100-O · Density: nominal, 20 °CAluminum 1100-O · Thermal conductivity: typical, O, 20 °CAluminum 1100-O · Thermal expansion: typical, mean 20-100 °CAluminum 1100-O · Melting point: melting range
Technical Datasheet, Extruded Products: Alloy EN AW-1050AHydroAluminum 1100-O · Specific heat: base material: commercially pure aluminium EN AW-1050A (Hydro), 20 °C
Each number points to the document that states it, with the exact basis. Values without a number are computed from the sourced ones. "Not sourced" means no citable source states it (or only a specification minimum); figures computed from it are left out too.
SLA Resin Tough 2000 is 3D printed: its properties depend on build direction and print settings; these are typical values.
Questions
Mechanical
Is Aluminum 1100-O stronger than SLA Resin Tough 2000?
SLA Resin Tough 2000 is stronger: its yield strength is 40.4 MPa against 35 MPa for Aluminum 1100-O (15%).
Which is lighter, Aluminum 1100-O or SLA Resin Tough 2000?
SLA Resin Tough 2000 is lighter: 1,090 kg/m³ against 2,710 kg/m³ for Aluminum 1100-O.
Which is stiffer, Aluminum 1100-O or SLA Resin Tough 2000?
Aluminum 1100-O is stiffer: Young's modulus 69 GPa against 1.8 GPa for SLA Resin Tough 2000, so the same part in Aluminum 1100-O deflects less under the same load.
Which is lighter for the same job, Aluminum 1100-O or SLA Resin Tough 2000?
For the same stiffness or strength: Aluminum 1100-O is lighter for a stiff rod or tie (tension), stiff beam (bending), stiff panel or plate; SLA Resin Tough 2000 is lighter for a strong rod or tie, strong beam, strong panel or plate.
Part that must be
Aluminum 1100-O
SLA Resin Tough 2000
Stiff rod or tie (tension)
lighter
15.4x heavier
Stiff beam (bending)
lighter
2.49x heavier
Stiff panel or plate
lighter
36% heavier
Strong rod or tie
2.87x heavier
lighter
Strong beam
2.74x heavier
lighter
Strong panel or plate
2.67x heavier
lighter
For the same stiffness or strength, mass scales with density over stiffness (or strength) raised to a power set by how the part is loaded: 1 for a rod in tension, 1/2 for a beam in bending, 1/3 for a panel (the standard material-selection indices).
Which is more ductile, Aluminum 1100-O or SLA Resin Tough 2000?
SLA Resin Tough 2000 stretches further before it breaks: 79% elongation at break against 35% for Aluminum 1100-O.
Thermal
Which expands less with temperature?
Aluminum 1100-O expands less: 23.6 µm/m·K against 134 µm/m·K for SLA Resin Tough 2000.