Thermal conductivity against densityHigher and further left: spreads more heat for its weightThermal expansion against thermal conductivityLower and further right: warps less when heated
Try it on a partA bracket to run stress or thermal on, free in your browser
Sources5 documents: Kaiser Aluminum, BASF Forward AM, U.S. Department of Defense, INEOS Styrolution
Aluminum 7075-T6
7075-T6/T651, Kaiser Aluminum rod & bar (mechanical) and sheet/coil/plate (physical) typical datasheets; Poisson from MIL-HDBK-5J
FDM HIPS
BASF Forward AM (BASF 3D Printing Solutions) Ultrafuse HiPS, TDS v2.2 (13.11.2019), printed specimens, XY 'Flat'. Specimen print settings are not stated; recommended processing on the sheet: nozzle 240-260 °C, bed 100-120 °C, 40-80 mm/s. Product is discontinued (Forward AM product page) but the TDS is still served by Forward AM.
1
Alloy 7075 Rod & Bar Technical DataKaiser Aluminumarchived copyAluminum 7075-T6 · Yield strength: typical, 0.2% offset, .500 in dia specimenAluminum 7075-T6 · Ultimate tensile strength: typicalAluminum 7075-T6 · Elongation at break: typical, in 4DAluminum 7075-T6 · Young's modulus (stiffness): typical
Alloy 7075 Sheet, Coil & Plate Technical DataKaiser Aluminumarchived copyAluminum 7075-T6 · Density: nominalAluminum 7075-T6 · Thermal conductivity: typical, 20 °C, T651Aluminum 7075-T6 · Thermal expansion: typical, mean 20-100 °CAluminum 7075-T6 · Specific heat: typical, at 100 °CAluminum 7075-T6 · Melting point: melting range
4
MIL-HDBK-5J, Metallic Materials and Elements for Aerospace Vehicle Structures (2003)U.S. Department of DefenseAluminum 7075-T6 · Poisson's ratio: typical (handbook physical constant)
Each number points to the document that states it, with the exact basis. Values without a number are computed from the sourced ones. "Not sourced" means no citable source states it (or only a specification minimum); figures computed from it are left out too.
FDM HIPS is 3D printed: its properties depend on build direction and print settings; these are typical values.
Questions
Mechanical
Is Aluminum 7075-T6 stronger than FDM HIPS?
Aluminum 7075-T6 is stronger: its yield strength is 503 MPa against tensile strength 18.4 MPa for FDM HIPS (27.3x).
Which is lighter, Aluminum 7075-T6 or FDM HIPS?
FDM HIPS is lighter: 1,023 kg/m³ against 2,800 kg/m³ for Aluminum 7075-T6.
Which is stiffer, Aluminum 7075-T6 or FDM HIPS?
Aluminum 7075-T6 is stiffer: Young's modulus 71 GPa against 1.59 GPa for FDM HIPS, so the same part in Aluminum 7075-T6 deflects less under the same load.
Which is lighter for the same job, Aluminum 7075-T6 or FDM HIPS?
For the same stiffness or strength: Aluminum 7075-T6 is lighter for a stiff rod or tie (tension), stiff beam (bending), stiff panel or plate, strong rod or tie, strong beam, strong panel or plate.
Part that must be
Aluminum 7075-T6
FDM HIPS
Stiff rod or tie (tension)
lighter
16.3x heavier
Stiff beam (bending)
lighter
2.44x heavier
Stiff panel or plate
lighter
30% heavier
Strong rod or tie
lighter
9.99x heavier
Strong beam
lighter
3.32x heavier
Strong panel or plate
lighter
1.91x heavier
For the same stiffness or strength, mass scales with density over stiffness (or strength) raised to a power set by how the part is loaded: 1 for a rod in tension, 1/2 for a beam in bending, 1/3 for a panel (the standard material-selection indices).
Which is more ductile, Aluminum 7075-T6 or FDM HIPS?
Aluminum 7075-T6 stretches further before it breaks: 11% elongation at break against 1.4% for FDM HIPS.
Thermal
Which conducts heat better, Aluminum 7075-T6 or FDM HIPS?
Aluminum 7075-T6 conducts heat better: 130 W/m·K against 0.17 W/m·K for FDM HIPS.
Which expands less with temperature?
Aluminum 7075-T6 expands less: 23.4 µm/m·K against 80 µm/m·K for FDM HIPS.