Thermal conductivity against densityHigher and further left: spreads more heat for its weightThermal expansion against thermal conductivityLower and further right: warps less when heated
Try it on a partA bracket to run stress or thermal on, free in your browser
Sources4 documents: Kaiser Aluminum, BASF Forward AM, U.S. Department of Defense, INEOS Styrolution
Aluminum
6061-T6/T651, Kaiser Aluminum typical properties (sheet, coil & plate datasheet); Poisson from MIL-HDBK-5J
FDM HIPS
BASF Forward AM (BASF 3D Printing Solutions) Ultrafuse HiPS, TDS v2.2 (13.11.2019), printed specimens, XY 'Flat'. Specimen print settings are not stated; recommended processing on the sheet: nozzle 240-260 °C, bed 100-120 °C, 40-80 mm/s. Product is discontinued (Forward AM product page) but the TDS is still served by Forward AM.
1
Alloy 6061 Sheet, Coil & Plate Technical DataKaiser Aluminumarchived copyAluminum · Yield strength: typical, 0.2% offset, .500 in dia specimenAluminum · Ultimate tensile strength: typicalAluminum · Elongation at break: typical, in 4D, 0.500 in dia specimenAluminum · Young's modulus (stiffness): typicalAluminum · Density: nominalAluminum · Thermal conductivity: typical, 20 °CAluminum · Thermal expansion: typical, mean 20-100 °CAluminum · Specific heat: typical, at 100 °CAluminum · Melting point: solidus-liquidus
MIL-HDBK-5J, Metallic Materials and Elements for Aerospace Vehicle Structures (2003)U.S. Department of DefenseAluminum · Poisson's ratio: typical (handbook physical constant)
Each number points to the document that states it, with the exact basis. Values without a number are computed from the sourced ones. "Not sourced" means no citable source states it (or only a specification minimum); figures computed from it are left out too.
FDM HIPS is 3D printed: its properties depend on build direction and print settings; these are typical values.
Questions
Mechanical
Is Aluminum stronger than FDM HIPS?
Aluminum is stronger: its yield strength is 276 MPa against tensile strength 18.4 MPa for FDM HIPS (15x).
Which is lighter, Aluminum or FDM HIPS?
FDM HIPS is lighter: 1,023 kg/m³ against 2,700 kg/m³ for Aluminum.
Which is stiffer, Aluminum or FDM HIPS?
Aluminum is stiffer: Young's modulus 68.3 GPa against 1.59 GPa for FDM HIPS, so the same part in Aluminum deflects less under the same load.
Which is lighter for the same job, Aluminum or FDM HIPS?
For the same stiffness or strength: Aluminum is lighter for a stiff rod or tie (tension), stiff beam (bending), stiff panel or plate, strong rod or tie, strong beam, strong panel or plate.
Part that must be
Aluminum
FDM HIPS
Stiff rod or tie (tension)
lighter
16.3x heavier
Stiff beam (bending)
lighter
2.48x heavier
Stiff panel or plate
lighter
33% heavier
Strong rod or tie
lighter
5.68x heavier
Strong beam
lighter
2.3x heavier
Strong panel or plate
lighter
47% heavier
For the same stiffness or strength, mass scales with density over stiffness (or strength) raised to a power set by how the part is loaded: 1 for a rod in tension, 1/2 for a beam in bending, 1/3 for a panel (the standard material-selection indices).
Which is more ductile, Aluminum or FDM HIPS?
Aluminum stretches further before it breaks: 17% elongation at break against 1.4% for FDM HIPS.
Thermal
Which conducts heat better, Aluminum or FDM HIPS?
Aluminum conducts heat better: 167 W/m·K against 0.17 W/m·K for FDM HIPS.
Which expands less with temperature?
Aluminum expands less: 23.6 µm/m·K against 80 µm/m·K for FDM HIPS.