Materials / Compare
Brass C260 vs. Plastic PBT GF30 Compare Brass C260 vs. Plastic PBT GF30 strength, stiffness, weight and thermal properties.
Change either side
Plastic PLA Plastic PETG Plastic ABS Plastic TPU Plastic Nylon Plastic ABS (bulk/injection) Plastic Polycarbonate Plastic POM/Acetal Plastic Nylon PA6 Plastic Nylon PA66 Plastic PEEK Plastic PTFE Plastic UHMWPE Plastic HDPE Plastic Polypropylene Plastic PMMA Plastic PBT GF30 Plastic PPS GF40 Plastic LCP GF30 Rubber Wood Aluminum Aluminum 6061-T6 Aluminum 7075-T6 Aluminum 2024-T351 Aluminum 5052-H32 Aluminum 7050-T7451 Aluminum A380 Aluminum 6063-T6 Aluminum 1100-O Aluminum ADC12 Steel Steel AISI 1018 Steel AISI 1045 Steel AISI 4340 Steel A992 Iron Titanium Titanium Ti-6Al-4V Stainless Steel 304 Stainless Steel 316 Stainless Steel 303 Stainless Steel 17-4PH Brass C360 Brass C260 Copper C110 Glass Nickel Inconel 718 Magnesium AZ31B-H24 Magnesium AZ91D Zinc Zamak 3 FDM ASA FDM Polycarbonate FDM PAHT-CF FDM HIPS SLA Resin Standard SLA Resin Tough 2000 SLA Resin Elastic 50A SLS PA12 Nylon DMLS AlSi10Mg Aluminum DMLS Ti-6Al-4V ELI Titanium DMLS 316L Stainless Steel DMLS 17-4PH Stainless Steel Concrete Brick Plywood Drywall PCB Laminate FR-4 Silicon Ceramic Alumina 96% Ceramic Aluminum Nitride Solder SAC305 Brass C260 Wrought Plastic PLA Plastic PETG Plastic ABS Plastic TPU Plastic Nylon Plastic ABS (bulk/injection) Plastic Polycarbonate Plastic POM/Acetal Plastic Nylon PA6 Plastic Nylon PA66 Plastic PEEK Plastic PTFE Plastic UHMWPE Plastic HDPE Plastic Polypropylene Plastic PMMA Plastic PBT GF30 Plastic PPS GF40 Plastic LCP GF30 Rubber Wood Aluminum Aluminum 6061-T6 Aluminum 7075-T6 Aluminum 2024-T351 Aluminum 5052-H32 Aluminum 7050-T7451 Aluminum A380 Aluminum 6063-T6 Aluminum 1100-O Aluminum ADC12 Steel Steel AISI 1018 Steel AISI 1045 Steel AISI 4340 Steel A992 Iron Titanium Titanium Ti-6Al-4V Stainless Steel 304 Stainless Steel 316 Stainless Steel 303 Stainless Steel 17-4PH Brass C360 Brass C260 Copper C110 Glass Nickel Inconel 718 Magnesium AZ31B-H24 Magnesium AZ91D Zinc Zamak 3 FDM ASA FDM Polycarbonate FDM PAHT-CF FDM HIPS SLA Resin Standard SLA Resin Tough 2000 SLA Resin Elastic 50A SLS PA12 Nylon DMLS AlSi10Mg Aluminum DMLS Ti-6Al-4V ELI Titanium DMLS 316L Stainless Steel DMLS 17-4PH Stainless Steel Concrete Brick Plywood Drywall PCB Laminate FR-4 Silicon Ceramic Alumina 96% Ceramic Aluminum Nitride Solder SAC305 Plastic PBT GF30 Bulk polymer (molded or machined) Try it on a partA bracket to run stress or thermal on, free in your browser Open in LessCAD Open in LessCAD Mechanical Yield strength 345 MPa source nominal, strip/flat, 0.5% extension (not 0.2% offset) not given (tensile used) Ultimate tensile strength 427 MPa source nominal, strip/flat 140 MPa source stress at break, 23 °C Flexural strength not sourced 210 MPa source typical, 23 °C Elongation at break 23 % source nominal, in 2.0 in., strip/flat 3 % source strain at break, 23 °C Young's modulus (stiffness) 110 GPa source typical, temper-independent 9.8 GPa source typical, 23 °C Density 8,525 kg/m³ source nominal 1,530 kg/m³ source typical Strength to weight 40.5 kN·m/kg 91.5 kN·m/kg 2.26x higher Stiffness to weight 12.9 MN·m/kg 2.02x higher 6.41 MN·m/kg Poisson's ratio 0.34 source reference value at room temperature (Wieland-M30 = CuZn30 = C26000, rolled products) not sourced Shear modulus 41.2 GPa not sourced Bulk modulus 115 GPa not sourced Speed of sound 3,597 m/s 2,531 m/s Thermal Thermal conductivity 121 W/m·K source typical, 20 °C 0.27 W/m·K source typical (DIN 52612-1) Thermal expansion 20 µm/m·K source typical, mean 20-300 °C 25 µm/m·K source longitudinal (flow), mean 23-55 °C 100 mm part over a 50 °C swing 100 µm growth 25% less 125 µm growth Specific heat 377 J/kg·K source typical, 20 °C 1,050 J/kg·K source typical, 23 °C Heats up and cools (diffusivity) 37.7 mm²/s 224x faster 0.168 mm²/s Thermal shock resistance 12,510 W/m not sourced Melting point 916–954 °C source solidus-liquidus 223 °C source DSC (ISO 11357) Max service temperature not sourced 205 °C source HDT 1.8 MPa Values for C26000 cartridge brass, H02 half hard flat/strip: CDA Electronic Connector Design Guide (mechanical) + CDA alloy page (physical) BASF Ultradur B 4300 G6 (PBT, 30% glass fibre), injection moulding grade; product information sheet 09/2026, typical values for uncoloured product at 23 °C.
Every value links to the document that states it. "Not sourced" means no citable source states it (or only a specification minimum); figures computed from it are left out too.
Questions Is Brass C260 stronger than Plastic PBT GF30? Brass C260 is stronger: its yield strength is 345 MPa against tensile strength 140 MPa for Plastic PBT GF30 (2.46x).
Which is lighter, Brass C260 or Plastic PBT GF30? Plastic PBT GF30 is lighter: 1,530 kg/m³ against 8,525 kg/m³ for Brass C260.
Which is stiffer, Brass C260 or Plastic PBT GF30? Brass C260 is stiffer: Young's modulus 110 GPa against 9.8 GPa for Plastic PBT GF30, so the same part in Brass C260 deflects less under the same load.
Which is lighter for the same job, Brass C260 or Plastic PBT GF30? For the same stiffness or strength: Brass C260 is lighter for a stiff rod or tie (tension); Plastic PBT GF30 is lighter for a stiff beam (bending), stiff panel or plate, strong rod or tie, strong beam, strong panel or plate.
Part that must be Brass C260 Plastic PBT GF30 Stiff rod or tie (tension) lighter 2.02x heavier Stiff beam (bending) 1.66x heavier lighter Stiff panel or plate 2.49x heavier lighter Strong rod or tie 2.26x heavier lighter Strong beam 3.05x heavier lighter Strong panel or plate 3.55x heavier lighter
For the same stiffness or strength, mass scales with density over stiffness (or strength) raised to a power set by how the part is loaded: 1 for a rod in tension, 1/2 for a beam in bending, 1/3 for a panel (the standard material-selection indices).
Which conducts heat better, Brass C260 or Plastic PBT GF30? Brass C260 conducts heat better: 121 W/m·K against 0.27 W/m·K for Plastic PBT GF30.
Which expands less with temperature? Brass C260 expands less: 20 µm/m·K against 25 µm/m·K for Plastic PBT GF30.
Among 72 materials 1k 10k 0.1 1 10 100 Density (kg/m³) Young's modulus (GPa) Plastic PLA Plastic PETG Plastic ABS Plastic TPU Plastic Nylon Aluminum Steel Iron Titanium Steel AISI 1018 Stainless Steel 304 Stainless Steel 316 Aluminum 6061-T6 Aluminum 7075-T6 Brass C360 Copper C110 Glass Steel AISI 1045 Steel AISI 4340 Steel A992 Stainless Steel 303 Stainless Steel 17-4PH Aluminum 2024-T351 Aluminum 5052-H32 Aluminum 7050-T7451 Titanium Ti-6Al-4V Nickel Inconel 718 Magnesium AZ31B-H24 Zinc Zamak 3 Plastic ABS (bulk/injection) Plastic Polycarbonate Plastic POM/Acetal Plastic Nylon PA6 Plastic Nylon PA66 Plastic PEEK Plastic UHMWPE Plastic HDPE Plastic Polypropylene Plastic PMMA FDM ASA FDM Polycarbonate FDM PAHT-CF FDM HIPS SLA Resin Tough 2000 SLS PA12 Nylon DMLS AlSi10Mg Aluminum DMLS Ti-6Al-4V ELI Titanium DMLS 316L Stainless Steel DMLS 17-4PH Stainless Steel PCB Laminate FR-4 Silicon Ceramic Alumina 96% Ceramic Aluminum Nitride Aluminum A380 Aluminum 6063-T6 Aluminum 1100-O Aluminum ADC12 Magnesium AZ91D Solder SAC305 Plastic PPS GF40 Plastic LCP GF30 Brass C260 Plastic PBT GF30 Stiffness against density 1k 10k 10 100 1k Density (kg/m³) Yield strength (MPa) Plastic PLA Plastic PETG Plastic ABS Plastic TPU Plastic Nylon Rubber Aluminum Steel Iron Titanium Steel AISI 1018 Stainless Steel 304 Stainless Steel 316 Aluminum 6061-T6 Aluminum 7075-T6 Brass C360 Copper C110 Glass Steel AISI 1045 Steel AISI 4340 Steel A992 Stainless Steel 303 Stainless Steel 17-4PH Aluminum 2024-T351 Aluminum 5052-H32 Aluminum 7050-T7451 Titanium Ti-6Al-4V Nickel Inconel 718 Magnesium AZ31B-H24 Zinc Zamak 3 Plastic ABS (bulk/injection) Plastic Polycarbonate Plastic POM/Acetal Plastic Nylon PA6 Plastic Nylon PA66 Plastic PEEK Plastic PTFE Plastic UHMWPE Plastic HDPE Plastic Polypropylene Plastic PMMA FDM ASA FDM Polycarbonate FDM PAHT-CF FDM HIPS SLA Resin Tough 2000 SLA Resin Elastic 50A SLS PA12 Nylon DMLS AlSi10Mg Aluminum DMLS Ti-6Al-4V ELI Titanium DMLS 316L Stainless Steel DMLS 17-4PH Stainless Steel Brick PCB Laminate FR-4 Silicon Ceramic Alumina 96% Aluminum A380 Aluminum 6063-T6 Aluminum 1100-O Aluminum ADC12 Magnesium AZ91D Solder SAC305 Plastic PPS GF40 Plastic LCP GF30 Brass C260 Plastic PBT GF30 Strength against density