Thermal conductivity against densityHigher and further left: spreads more heat for its weightThermal expansion against thermal conductivityLower and further right: warps less when heated
Try it on a partA bracket to run stress or thermal on, free in your browser
Makrolon 2405 Technical Data SheetCovestroPlastic Polycarbonate · Yield strength: typical, tensile yieldPlastic Polycarbonate · Ultimate tensile strength: typical, stress at breakPlastic Polycarbonate · Flexural strength: typical, flexural strengthPlastic Polycarbonate · Elongation at break: typical, strain at breakPlastic Polycarbonate · Young's modulus (stiffness): typicalPlastic Polycarbonate · Density: typicalPlastic Polycarbonate · Thermal conductivity: typical, through-plane, 23 CPlastic Polycarbonate · Thermal expansion: typical, 23-55 C, parallel and normalPlastic Polycarbonate · Glass transition: typical, DSC 10 C/minPlastic Polycarbonate · Max service temperature: UL 746B RTI, tensile strength, 1.5 mm
3
Wieland-Z30 (CuZn39Pb2, C37700) Data SheetWielandarchived copyBrass C360 · Poisson's ratio: base material: leaded free-machining brass CuZn39Pb2 (C37700), Wieland-Z30 rolled products, reference value at room temperature
4
Engineering Polymers Part and Mold Design: Thermoplastics, A Design GuideCovestroarchived copyPlastic Polycarbonate · Poisson's ratio: typical, polycarbonate family (Covestro Part and Mold Design guide, Table 3-1)
5
Makrolon 2405 Data Sheet, ASTM valuesBayer MaterialSciencearchived copyPlastic Polycarbonate · Specific heat: typical (guide value), Bayer ASTM datasheet for Makrolon 2405, ASTM D 2766
Each number points to the document that states it, with the exact basis. Values without a number are computed from the sourced ones. "Not sourced" means no citable source states it (or only a specification minimum); figures computed from it are left out too.
Questions
Mechanical
Is Brass C360 stronger than Plastic Polycarbonate?
Brass C360 is stronger: its yield strength is 310 MPa against 65 MPa for Plastic Polycarbonate (4.77x).
Which is lighter, Brass C360 or Plastic Polycarbonate?
Plastic Polycarbonate is lighter: 1,200 kg/m³ against 8,498 kg/m³ for Brass C360.
Which is stiffer, Brass C360 or Plastic Polycarbonate?
Brass C360 is stiffer: Young's modulus 96.5 GPa against 2.4 GPa for Plastic Polycarbonate, so the same part in Brass C360 deflects less under the same load.
Which is lighter for the same job, Brass C360 or Plastic Polycarbonate?
For the same stiffness or strength: Brass C360 is lighter for a stiff rod or tie (tension); Plastic Polycarbonate is lighter for a stiff beam (bending), stiff panel or plate, strong rod or tie, strong beam, strong panel or plate.
Part that must be
Brass C360
Plastic Polycarbonate
Stiff rod or tie (tension)
lighter
5.68x heavier
Stiff beam (bending)
12% heavier
lighter
Stiff panel or plate
2.07x heavier
lighter
Strong rod or tie
48% heavier
lighter
Strong beam
2.5x heavier
lighter
Strong panel or plate
3.24x heavier
lighter
For the same stiffness or strength, mass scales with density over stiffness (or strength) raised to a power set by how the part is loaded: 1 for a rod in tension, 1/2 for a beam in bending, 1/3 for a panel (the standard material-selection indices).
Which is more ductile, Brass C360 or Plastic Polycarbonate?
Plastic Polycarbonate stretches further before it breaks: 125% elongation at break against 25% for Brass C360.
Thermal
Which conducts heat better, Brass C360 or Plastic Polycarbonate?
Brass C360 conducts heat better: 116 W/m·K against 0.2 W/m·K for Plastic Polycarbonate.
Which expands less with temperature?
Brass C360 expands less: 20.5 µm/m·K against 65 µm/m·K for Plastic Polycarbonate.