Thermal conductivity against densityHigher and further left: spreads more heat for its weightThermal expansion against thermal conductivityLower and further right: warps less when heated
Try it on a partA bracket to run stress or thermal on, free in your browser
Sources3 documents: Copper Development Association, Formlabs, Wieland
Brass C360
C36000 free-cutting brass, H02 half-hard rod 1 in. section (20% cold work), copper.org typical values
SLA Resin Tough 2000
Formlabs Tough 2000 Resin V2 (FLTO2002), TDS Rev. 01 10/06/2025; printed on Form 4 at 100 µm, washed in Form Wash V2 10+5 min in >=99% IPA, post-cured 70 °C for 12 min in Form Cure V2. Orientation not stated.
Wieland-Z30 (CuZn39Pb2, C37700) Data SheetWielandarchived copyBrass C360 · Poisson's ratio: base material: leaded free-machining brass CuZn39Pb2 (C37700), Wieland-Z30 rolled products, reference value at room temperature
Each number points to the document that states it, with the exact basis. Values without a number are computed from the sourced ones. "Not sourced" means no citable source states it (or only a specification minimum); figures computed from it are left out too.
SLA Resin Tough 2000 is 3D printed: its properties depend on build direction and print settings; these are typical values.
Questions
Mechanical
Is Brass C360 stronger than SLA Resin Tough 2000?
Brass C360 is stronger: its yield strength is 310 MPa against 40.4 MPa for SLA Resin Tough 2000 (7.67x).
Which is lighter, Brass C360 or SLA Resin Tough 2000?
SLA Resin Tough 2000 is lighter: 1,090 kg/m³ against 8,498 kg/m³ for Brass C360.
Which is stiffer, Brass C360 or SLA Resin Tough 2000?
Brass C360 is stiffer: Young's modulus 96.5 GPa against 1.8 GPa for SLA Resin Tough 2000, so the same part in Brass C360 deflects less under the same load.
Which is lighter for the same job, Brass C360 or SLA Resin Tough 2000?
For the same stiffness or strength: Brass C360 is lighter for a stiff rod or tie (tension); SLA Resin Tough 2000 is lighter for a stiff beam (bending), stiff panel or plate, strong rod or tie, strong beam, strong panel or plate.
Part that must be
Brass C360
SLA Resin Tough 2000
Stiff rod or tie (tension)
lighter
6.88x heavier
Stiff beam (bending)
6% heavier
lighter
Stiff panel or plate
2.07x heavier
lighter
Strong rod or tie
2% heavier
lighter
Strong beam
2x heavier
lighter
Strong panel or plate
2.81x heavier
lighter
For the same stiffness or strength, mass scales with density over stiffness (or strength) raised to a power set by how the part is loaded: 1 for a rod in tension, 1/2 for a beam in bending, 1/3 for a panel (the standard material-selection indices).
Which is more ductile, Brass C360 or SLA Resin Tough 2000?
SLA Resin Tough 2000 stretches further before it breaks: 79% elongation at break against 25% for Brass C360.
Thermal
Which expands less with temperature?
Brass C360 expands less: 20.5 µm/m·K against 134 µm/m·K for SLA Resin Tough 2000.