Thermal conductivity against densityHigher and further left: spreads more heat for its weightThermal expansion against thermal conductivityLower and further right: warps less when heated
Try it on a partA sample part to run stress or thermal on, free in your browser
Sources6 documents: BASF, National Institute of Standards and Technology, Brick Industry Association, Covestro
Brick
Solid extruded clay/shale brick units (BIA 1993 manufacturer survey, TN 3A 2024); face brick of 130 lb/ft3 for thermal properties (BIA TN 4, from ASHRAE 2013); CTE is the TMS Code value for clay/shale masonry
Plastic Nylon PA66
BASF Ultramid A3K (PA66, unreinforced injection-moulding grade), Product Information 02/2026, dry values (ISO methods)
Strength of Masonry Walls Under Compressive and Transverse Loads (Building Science Series 34)National Institute of Standards and Technologyarchived copyBrick · Ultimate tensile strength: modulus of rupture (no direct tensile value)
3
Technical Notes 3A: Brick Masonry Material PropertiesBrick Industry AssociationBrick · Compressive strength: mean unit compressive strength, solid extruded brick (survey mean; SD 30.8 MPa)Brick · Thermal expansion: TMS Code average coefficient, clay/shale unit masonry
4
Technical Notes 4: Introduction to Energy Performance of Brick Masonry (2016)Brick Industry Associationarchived copyBrick · Density: face brick density row used for k (BIA notes most fired clay brick 120-130 lb/ft3)Brick · Thermal conductivity: range for 130 lb/ft3 face brick (ASHRAE 2013 via BIA)
5
Engineering Polymers Part and Mold Design: Thermoplastics, A Design GuideCovestroPlastic Nylon PA66 · Poisson's ratio: base material: unfilled polyamide (PA), conditioned, maker design-guide family value (Covestro Table 3-1)
6
Technical Notes 4B: Energy Code Compliance of Brick Masonry WallsBrick Industry Associationarchived copyBrick · Specific heat: value used in BIA heat-capacity sample calculation
Each number points to the document that states it, with the exact basis. Values without a number are computed from the sourced ones. "Not sourced" means no citable source states it (or only a specification minimum); figures computed from it are left out too.
Questions
Mechanical
Is Brick stronger than Plastic Nylon PA66?
Plastic Nylon PA66 is stronger: its yield strength is 85 MPa against tensile strength 5.1 MPa for Brick (16.7x).
Which is lighter, Brick or Plastic Nylon PA66?
Plastic Nylon PA66 is lighter: 1,130 kg/m³ against 2,082 kg/m³ for Brick.
Which is lighter for the same job, Brick or Plastic Nylon PA66?
For the same stiffness or strength: Plastic Nylon PA66 is lighter for a strong rod or tie, strong beam, strong panel or plate.
Part that must be
Brick
Plastic Nylon PA66
Strong rod or tie
30.7x heavier
lighter
Strong beam
12x heavier
lighter
Strong panel or plate
7.52x heavier
lighter
For the same stiffness or strength, mass scales with density over stiffness (or strength) raised to a power set by how the part is loaded: 1 for a rod in tension, 1/2 for a beam in bending, 1/3 for a panel (the standard material-selection indices).
Thermal
Which conducts heat better, Brick or Plastic Nylon PA66?
Brick conducts heat better: 1.02 W/m·K against 0.33 W/m·K for Plastic Nylon PA66.
Which expands less with temperature?
Brick expands less: 7.2 µm/m·K against 98 µm/m·K for Plastic Nylon PA66.