Thermal conductivity against densityHigher and further left: spreads more heat for its weightThermal expansion against thermal conductivityLower and further right: warps less when heated
Try it on a partA bracket to run stress or thermal on, free in your browser
Hostalen 23050 B Product DataLyondellBasellPlastic HDPE · Yield strength: typical, tensile stress at yield 23 °C, 50 mm/min ISO 527Plastic HDPE · Young's modulus (stiffness): typical, tensile modulus 23 °C ISO 527Plastic HDPE · Density: typical, ISO 1183
3
Wieland-K32 (Cu-ETP, C11000) Data SheetWielandarchived copyCopper C110 · Poisson's ratio: reference value at room temperature (Wieland-K32 = Cu-ETP = C11000, rolled products)
4
Typical Engineering Properties of High Density PolyethyleneINEOS Olefins & Polymers USAarchived copyPlastic HDPE · Poisson's ratio: base material: high-density polyethylene family (INEOS Olefins & Polymers USA, Typical Engineering Properties of HDPE)Plastic HDPE · Thermal conductivity: base material: high-density polyethylene family (INEOS Olefins & Polymers USA, Typical Engineering Properties of HDPE)Plastic HDPE · Thermal expansion: base material: high-density polyethylene family (INEOS Olefins & Polymers USA, Typical Engineering Properties of HDPE)Plastic HDPE · Specific heat: base material: high-density polyethylene family (INEOS Olefins & Polymers USA, Typical Engineering Properties of HDPE)
Each number points to the document that states it, with the exact basis. Values without a number are computed from the sourced ones. "Not sourced" means no citable source states it (or only a specification minimum); figures computed from it are left out too.
Questions
Mechanical
Is Copper C110 stronger than Plastic HDPE?
Copper C110 is stronger: its yield strength is 69 MPa against 24 MPa for Plastic HDPE (2.88x).
Which is lighter, Copper C110 or Plastic HDPE?
Plastic HDPE is lighter: 950 kg/m³ against 8,913 kg/m³ for Copper C110.
Which is stiffer, Copper C110 or Plastic HDPE?
Copper C110 is stiffer: Young's modulus 117 GPa against 0.9 GPa for Plastic HDPE, so the same part in Copper C110 deflects less under the same load.
Which is lighter for the same job, Copper C110 or Plastic HDPE?
For the same stiffness or strength: Copper C110 is lighter for a stiff rod or tie (tension), stiff beam (bending); Plastic HDPE is lighter for a stiff panel or plate, strong rod or tie, strong beam, strong panel or plate.
Part that must be
Copper C110
Plastic HDPE
Stiff rod or tie (tension)
lighter
13.9x heavier
Stiff beam (bending)
lighter
22% heavier
Stiff panel or plate
1.85x heavier
lighter
Strong rod or tie
3.26x heavier
lighter
Strong beam
4.64x heavier
lighter
Strong panel or plate
5.53x heavier
lighter
For the same stiffness or strength, mass scales with density over stiffness (or strength) raised to a power set by how the part is loaded: 1 for a rod in tension, 1/2 for a beam in bending, 1/3 for a panel (the standard material-selection indices).
Thermal
Which conducts heat better, Copper C110 or Plastic HDPE?
Copper C110 conducts heat better: 391 W/m·K against 0.445 W/m·K for Plastic HDPE.
Which expands less with temperature?
Copper C110 expands less: 16.9 µm/m·K against 120 µm/m·K for Plastic HDPE.