Thermal conductivity against densityHigher and further left: spreads more heat for its weightThermal expansion against thermal conductivityLower and further right: warps less when heated
Try it on a partA bracket to run stress or thermal on, free in your browser
Sources4 documents: Copper Development Association, Celanese, Wieland
Copper C110
C11000 ETP copper, annealed to 0.050 mm grain size (OS050), 1 in. rod, copper.org typical values
Plastic UHMWPE
Celanese GUR 4120 (avg. molecular weight 4.7x10^6 g/mol), typical values on compression-molded specimens; CTE and thermal conductivity from Celanese's generic UHMWPE guide (grade not named)
GUR UHMW-PE Overview (GUR-015)CelanesePlastic UHMWPE · Yield strength: typical, tensile stress at yield ISO 527, 50 mm/minPlastic UHMWPE · Ultimate tensile strength: typical, tensile stress at break ISO 527, 50 mm/minPlastic UHMWPE · Elongation at break: typical, nominal elongation at break ISO 527Plastic UHMWPE · Young's modulus (stiffness): typical, tensile modulus ISO 527, 1 mm/minPlastic UHMWPE · Density: typicalPlastic UHMWPE · Melting point: DSC 10 K/minPlastic UHMWPE · Max service temperature: recommended max constant operating temperature
3
Wieland-K32 (Cu-ETP, C11000) Data SheetWielandarchived copyCopper C110 · Poisson's ratio: reference value at room temperature (Wieland-K32 = Cu-ETP = C11000, rolled products)
4
GUR UHMW-PE Polymer Guide (GUR-003)Celanesearchived copyPlastic UHMWPE · Thermal conductivity: typical, unfilled (narrative value, generic Celanese UHMWPE)Plastic UHMWPE · Thermal expansion: typical, 20 to 100 °C (generic Celanese UHMWPE)
Each number points to the document that states it, with the exact basis. Values without a number are computed from the sourced ones. "Not sourced" means no citable source states it (or only a specification minimum); figures computed from it are left out too.
Questions
Mechanical
Is Copper C110 stronger than Plastic UHMWPE?
Copper C110 is stronger: its yield strength is 69 MPa against 20 MPa for Plastic UHMWPE (3.45x).
Which is lighter, Copper C110 or Plastic UHMWPE?
Plastic UHMWPE is lighter: 930 kg/m³ against 8,913 kg/m³ for Copper C110.
Which is stiffer, Copper C110 or Plastic UHMWPE?
Copper C110 is stiffer: Young's modulus 117 GPa against 0.66 GPa for Plastic UHMWPE, so the same part in Copper C110 deflects less under the same load.
Which is lighter for the same job, Copper C110 or Plastic UHMWPE?
For the same stiffness or strength: Copper C110 is lighter for a stiff rod or tie (tension), stiff beam (bending); Plastic UHMWPE is lighter for a stiff panel or plate, strong rod or tie, strong beam, strong panel or plate.
Part that must be
Copper C110
Plastic UHMWPE
Stiff rod or tie (tension)
lighter
18.5x heavier
Stiff beam (bending)
lighter
39% heavier
Stiff panel or plate
1.71x heavier
lighter
Strong rod or tie
2.78x heavier
lighter
Strong beam
4.2x heavier
lighter
Strong panel or plate
5.16x heavier
lighter
For the same stiffness or strength, mass scales with density over stiffness (or strength) raised to a power set by how the part is loaded: 1 for a rod in tension, 1/2 for a beam in bending, 1/3 for a panel (the standard material-selection indices).
Which is more ductile, Copper C110 or Plastic UHMWPE?
Plastic UHMWPE stretches further before it breaks: 465% elongation at break against 55% for Copper C110.
Thermal
Which conducts heat better, Copper C110 or Plastic UHMWPE?
Copper C110 conducts heat better: 391 W/m·K against 0.4 W/m·K for Plastic UHMWPE.
Which expands less with temperature?
Copper C110 expands less: 16.9 µm/m·K against 200 µm/m·K for Plastic UHMWPE.