Thermal conductivity against densityHigher and further left: spreads more heat for its weightThermal expansion against thermal conductivityLower and further right: warps less when heated
Try it on a partA bracket to run stress or thermal on, free in your browser
Sources5 documents: Copper Development Association, Formlabs, Wieland
Copper C110
C11000 ETP copper, annealed to 0.050 mm grain size (OS050), 1 in. rod, copper.org typical values
SLA Resin Standard
Formlabs Clear Resin V5 (FLGPCL05), TDS Rev. 01 March 20, 2024; printed on Form 4 at 100 µm, washed 5 min in >=99% IPA, post-cured 15 min at 60 °C in Form Cure. Orientation not stated.
Clear Resin V5 Technical Data Sheet (2024)Formlabsarchived copySLA Resin Standard · Ultimate tensile strength: typicalSLA Resin Standard · Flexural strength: typicalSLA Resin Standard · Elongation at break: typicalSLA Resin Standard · Young's modulus (stiffness): typicalSLA Resin Standard · Max service temperature: HDT 1.8 MPa
3
Clear Resin V5 Technical Data Sheet (web edition)FormlabsSLA Resin Standard · Density: typical, post-cured (same for 5 min ambient and 15 min at 60 °C), ASTM D792
4
Wieland-K32 (Cu-ETP, C11000) Data SheetWielandarchived copyCopper C110 · Poisson's ratio: reference value at room temperature (Wieland-K32 = Cu-ETP = C11000, rolled products)
5
Thermal Properties of Selected Formlabs SLA ResinsFormlabsSLA Resin Standard · Thermal conductivity: typical, post-cured, ASTM E1530SLA Resin Standard · Thermal expansion: mean -30 to 140 °C, post-cured (5 min ambient cure), TMA ASTM E831SLA Resin Standard · Specific heat: typical, 25 °C, post-cured (5 min ambient cure), DSC ASTM E1269
Each number points to the document that states it, with the exact basis. Values without a number are computed from the sourced ones. "Not sourced" means no citable source states it (or only a specification minimum); figures computed from it are left out too.
SLA Resin Standard is 3D printed: its properties depend on build direction and print settings; these are typical values.
Questions
Mechanical
Is Copper C110 stronger than SLA Resin Standard?
Copper C110 is stronger: its yield strength is 69 MPa against tensile strength 60 MPa for SLA Resin Standard (15%).
Which is lighter, Copper C110 or SLA Resin Standard?
SLA Resin Standard is lighter: 1,210 kg/m³ against 8,913 kg/m³ for Copper C110.
Which is stiffer, Copper C110 or SLA Resin Standard?
Copper C110 is stiffer: Young's modulus 117 GPa against 2.75 GPa for SLA Resin Standard, so the same part in Copper C110 deflects less under the same load.
Which is lighter for the same job, Copper C110 or SLA Resin Standard?
For the same stiffness or strength: Copper C110 is lighter for a stiff rod or tie (tension); SLA Resin Standard is lighter for a stiff beam (bending), stiff panel or plate, strong rod or tie, strong beam, strong panel or plate.
Part that must be
Copper C110
SLA Resin Standard
Stiff rod or tie (tension)
lighter
5.79x heavier
Stiff beam (bending)
13% heavier
lighter
Stiff panel or plate
2.11x heavier
lighter
Strong rod or tie
6.41x heavier
lighter
Strong beam
6.71x heavier
lighter
Strong panel or plate
6.87x heavier
lighter
For the same stiffness or strength, mass scales with density over stiffness (or strength) raised to a power set by how the part is loaded: 1 for a rod in tension, 1/2 for a beam in bending, 1/3 for a panel (the standard material-selection indices).
Which is more ductile, Copper C110 or SLA Resin Standard?
Copper C110 stretches further before it breaks: 55% elongation at break against 8% for SLA Resin Standard.
Thermal
Which conducts heat better, Copper C110 or SLA Resin Standard?
Copper C110 conducts heat better: 391 W/m·K against 0.54 W/m·K for SLA Resin Standard.
Which expands less with temperature?
Copper C110 expands less: 16.9 µm/m·K against 114 µm/m·K for SLA Resin Standard.