Materials / Compare
DMLS Ti-6Al-4V ELI Titanium vs. SLA Resin Standard
Compare DMLS Ti-6Al-4V ELI Titanium vs. SLA Resin Standard strength, stiffness, weight and thermal properties.
| Mechanical | DMLS Ti-6Al-4V ELI Titanium | SLA Resin Standard |
|---|---|---|
| Yield strength | 1,100MPa1 | not given (tensile used) |
| Ultimate tensile strength | 1,270MPa121.2x stronger | 60MPa2 |
| Flexural strength | not sourced | 105MPa2 |
| Elongation at break | 8.7%1 | 8%2 |
| Young's modulus (stiffness) | same maker and process110GPa340x stiffer | 2.75GPa2 |
| Density | 4,400kg/m³1 | 1,210kg/m³43.64x lighter |
| Strength to weight | 250kN·m/kg5.04x higher | 49.6kN·m/kg |
| Stiffness to weight | 25MN·m/kg11x higher | 2.27MN·m/kg |
| Poisson's ratio | wrought TIMETAL 6-40.3425 | not sourced |
| Shear modulus | 41GPa | not sourced |
| Bulk modulus | 116GPa | not sourced |
| Speed of sound | 5,000m/s3.32x faster | 1,508m/s |
| Thermal | DMLS Ti-6Al-4V ELI Titanium | SLA Resin Standard |
|---|---|---|
| Thermal conductivity | base material6.6W/m·K612.2x more heat through a fin | 0.54W/m·K7 |
| Thermal expansion | mean 25-100 °C9µm/m·K812.7x less | mean -30 to 140 °C114µm/m·K7 |
| 100 mm part over a 50 °C swing | 45µm growth12.7x less | 571µm growth |
| Specific heat | base material580J/kg·K6 | 1,800J/kg·K73.1x higher |
| Heats up and cools (diffusivity) | 2.59mm²/s10.4x faster | 0.248mm²/s |
| Thermal shock resistance | 4,825W/m | not sourced |
| Melting point | melting range1,630–1,650°C5 | not sourced |
| Max service temperature | not sourced | HDT 1.8 MPa59°C2 |
| Try it on a partA bracket to run stress or thermal on, free in your browser | Open in LessCAD | Open in LessCAD |
|---|
Sources8 documents: EOS GmbH, Formlabs, TIMET
- DMLS Ti-6Al-4V ELI Titanium
- EOS Titanium Ti64ELI (powder 9011-0040; ASTM F136/F3001, i.e. Grade 23) on EOS M400 SF, parameter set Ti64ELI_030_FlexM400_100, 30 µm, as built; ISO 6892-1 A14
- SLA Resin Standard
- Formlabs Clear Resin V5 (FLGPCL05), TDS Rev. 01 March 20, 2024; printed on Form 4 at 100 µm, washed 5 min in >=99% IPA, post-cured 15 min at 60 °C in Form Cure. Orientation not stated.
- 1EOS Titanium Ti64ELI Material Data Sheet, M 290 and M 400EOS GmbHarchived copyDMLS Ti-6Al-4V ELI Titanium · Yield strength: typical, as built, average of horizontal + vertical (M400)DMLS Ti-6Al-4V ELI Titanium · Ultimate tensile strength: typical, as built, average of horizontal + vertical (M400)DMLS Ti-6Al-4V ELI Titanium · Elongation at break: typical at break, as built (M400)DMLS Ti-6Al-4V ELI Titanium · Density: typical part density (ISO 3369), M400
- 2Clear Resin V5 Technical Data Sheet (2024)Formlabsarchived copySLA Resin Standard · Ultimate tensile strength: typicalSLA Resin Standard · Flexural strength: typicalSLA Resin Standard · Elongation at break: typicalSLA Resin Standard · Young's modulus (stiffness): typicalSLA Resin Standard · Max service temperature: HDT 1.8 MPa
- 3EOS Titanium Ti64 Material Data Sheet, M 290 (2022)EOS GmbHarchived copyDMLS Ti-6Al-4V ELI Titanium · Young's modulus (stiffness): same maker and process, sibling grade: EOS Titanium Ti64 (Grade 5) on EOS M 290, as built, XY and Z, typical
- 4Clear Resin V5 Technical Data Sheet (web edition)FormlabsSLA Resin Standard · Density: typical, post-cured (same for 5 min ambient and 15 min at 60 °C), ASTM D792
- 5TIMETAL 6-4 PropertiesTIMETarchived copyDMLS Ti-6Al-4V ELI Titanium · Poisson's ratio: wrought TIMETAL 6-4 (TIMET measurement, mean of 10); composition-level, not DMLS-measuredDMLS Ti-6Al-4V ELI Titanium · Melting point: melting range, wrought TIMETAL 6-4 (composition-level)
- 6TIMETAL 6-4 Data SheetTIMETarchived copyDMLS Ti-6Al-4V ELI Titanium · Thermal conductivity: base material: wrought Ti-6Al-4V / 6-4 ELI (TIMET datasheet), 20 °CDMLS Ti-6Al-4V ELI Titanium · Specific heat: base material: wrought Ti-6Al-4V / 6-4 ELI (TIMET datasheet), 20 °C
- 7Thermal Properties of Selected Formlabs SLA ResinsFormlabsSLA Resin Standard · Thermal conductivity: typical, post-cured, ASTM E1530SLA Resin Standard · Thermal expansion: mean -30 to 140 °C, post-cured (5 min ambient cure), TMA ASTM E831SLA Resin Standard · Specific heat: typical, 25 °C, post-cured (5 min ambient cure), DSC ASTM E1269
- 8EOS Titanium Ti64 Grade 23 Material Data SheetEOS GmbHarchived copyDMLS Ti-6Al-4V ELI Titanium · Thermal expansion: mean 25-100 °C, ASTM E228; EOS Ti64 Grade 23 (=ELI) on EOS M 290 40 µm; condition not stated (sheet's mechanical data are heat treated)
Each number points to the document that states it, with the exact basis. Values without a number are computed from the sourced ones. "Not sourced" means no citable source states it (or only a specification minimum); figures computed from it are left out too.
DMLS Ti-6Al-4V ELI Titanium and SLA Resin Standard are 3D printed: their properties depend on build direction and print settings; these are typical values.
Questions
Mechanical
Is DMLS Ti-6Al-4V ELI Titanium stronger than SLA Resin Standard?
DMLS Ti-6Al-4V ELI Titanium is stronger: its yield strength is 1,100 MPa against tensile strength 60 MPa for SLA Resin Standard (18.3x).
Which is lighter, DMLS Ti-6Al-4V ELI Titanium or SLA Resin Standard?
SLA Resin Standard is lighter: 1,210 kg/m³ against 4,400 kg/m³ for DMLS Ti-6Al-4V ELI Titanium.
Which is stiffer, DMLS Ti-6Al-4V ELI Titanium or SLA Resin Standard?
DMLS Ti-6Al-4V ELI Titanium is stiffer: Young's modulus 110 GPa against 2.75 GPa for SLA Resin Standard, so the same part in DMLS Ti-6Al-4V ELI Titanium deflects less under the same load.
Which is lighter for the same job, DMLS Ti-6Al-4V ELI Titanium or SLA Resin Standard?
For the same stiffness or strength: DMLS Ti-6Al-4V ELI Titanium is lighter for a stiff rod or tie (tension), stiff beam (bending), strong rod or tie, strong beam, strong panel or plate; SLA Resin Standard is lighter for a stiff panel or plate.
| Part that must be | DMLS Ti-6Al-4V ELI Titanium | SLA Resin Standard |
|---|---|---|
| Stiff rod or tie (tension) | lighter | 11x heavier |
| Stiff beam (bending) | lighter | 1.74x heavier |
| Stiff panel or plate | 6% heavier | lighter |
| Strong rod or tie | lighter | 5.04x heavier |
| Strong beam | lighter | 1.91x heavier |
| Strong panel or plate | lighter | 18% heavier |
For the same stiffness or strength, mass scales with density over stiffness (or strength) raised to a power set by how the part is loaded: 1 for a rod in tension, 1/2 for a beam in bending, 1/3 for a panel (the standard material-selection indices).
Thermal
Which conducts heat better, DMLS Ti-6Al-4V ELI Titanium or SLA Resin Standard?
DMLS Ti-6Al-4V ELI Titanium conducts heat better: 6.6 W/m·K against 0.54 W/m·K for SLA Resin Standard.
Which expands less with temperature?
DMLS Ti-6Al-4V ELI Titanium expands less: 9 µm/m·K against 114 µm/m·K for SLA Resin Standard.
Related comparisons
- DMLS Ti-6Al-4V ELI Titanium vs. Titanium
- DMLS Ti-6Al-4V ELI Titanium vs. Titanium Ti-6Al-4V
- DMLS Ti-6Al-4V ELI Titanium vs. Stainless Steel 17-4PH
- DMLS Ti-6Al-4V ELI Titanium vs. Steel AISI 4340
- SLA Resin Standard vs. Plastic Polycarbonate
- SLA Resin Standard vs. Plastic Nylon
- SLA Resin Standard vs. FDM Polycarbonate
- SLA Resin Standard vs. Plastic POM/Acetal