Materials / Compare
DMLS Ti-6Al-4V ELI Titanium vs. Zinc Zamak 3
Compare DMLS Ti-6Al-4V ELI Titanium vs. Zinc Zamak 3 strength, stiffness, weight and thermal properties.
| Mechanical | DMLS Ti-6Al-4V ELI Titanium | Zinc Zamak 3 |
|---|---|---|
| Yield strength | 1,100MPa14.98x stronger | 221MPa2 |
| Ultimate tensile strength | 1,270MPa14.49x stronger | 283MPa2 |
| Elongation at break | 8.7%1 | 10%215% more ductile |
| Young's modulus (stiffness) | same maker and process110GPa329% stiffer | 85.5GPa2 |
| Density | 4,400kg/m³11.5x lighter | 6,600kg/m³2 |
| Strength to weight | 250kN·m/kg7.47x higher | 33.5kN·m/kg |
| Stiffness to weight | 25MN·m/kg1.93x higher | 13MN·m/kg |
| Poisson's ratio | wrought TIMETAL 6-40.3424 | 0.275 |
| Shear modulus | 41GPa22% stiffer in shear | 33.7GPa |
| Bulk modulus | 116GPa1.87x higher | 62GPa |
| Speed of sound | 5,000m/s39% faster | 3,599m/s |
| Thermal | DMLS Ti-6Al-4V ELI Titanium | Zinc Zamak 3 |
|---|---|---|
| Thermal conductivity | base material6.6W/m·K6 | 113W/m·K217.1x more heat through a fin |
| Thermal expansion | mean 25-100 °C9µm/m·K73.04x less | 27.4µm/m·K2 |
| 100 mm part over a 50 °C swing | 45µm growth3.04x less | 137µm growth |
| Specific heat | base material580J/kg·K639% higher | 419J/kg·K2 |
| Heats up and cools (diffusivity) | 2.59mm²/s | 40.9mm²/s15.8x faster |
| Thermal shock resistance | 4,825W/m | 7,782W/m1.61x more resistant |
| Melting point | melting range1,630–1,650°C4 | melting range381–387°C2 |
| Try it on a partA bracket to run stress or thermal on, free in your browser | Open in LessCAD | Open in LessCAD |
|---|
Sources7 documents: EOS GmbH, Nathan Trotter, TIMET, Eastern Alloys
- DMLS Ti-6Al-4V ELI Titanium
- EOS Titanium Ti64ELI (powder 9011-0040; ASTM F136/F3001, i.e. Grade 23) on EOS M400 SF, parameter set Ti64ELI_030_FlexM400_100, 30 µm, as built; ISO 6892-1 A14
- Zinc Zamak 3
- Zamak 3 (ASTM B86 die cast), Nathan Trotter (zinc alloy producer) technical data sheet, typical values
- 1EOS Titanium Ti64ELI Material Data Sheet, M 290 and M 400EOS GmbHarchived copyDMLS Ti-6Al-4V ELI Titanium · Yield strength: typical, as built, average of horizontal + vertical (M400)DMLS Ti-6Al-4V ELI Titanium · Ultimate tensile strength: typical, as built, average of horizontal + vertical (M400)DMLS Ti-6Al-4V ELI Titanium · Elongation at break: typical at break, as built (M400)DMLS Ti-6Al-4V ELI Titanium · Density: typical part density (ISO 3369), M400
- 2Zamak 3 Technical Data SheetNathan Trotterarchived copyZinc Zamak 3 · Yield strength: typicalZinc Zamak 3 · Ultimate tensile strength: typicalZinc Zamak 3 · Elongation at break: typical, in 2 in.Zinc Zamak 3 · Young's modulus (stiffness): typicalZinc Zamak 3 · Density: typicalZinc Zamak 3 · Thermal conductivity: typicalZinc Zamak 3 · Thermal expansion: typicalZinc Zamak 3 · Specific heat: typicalZinc Zamak 3 · Melting point: melting range
- 3EOS Titanium Ti64 Material Data Sheet, M 290 (2022)EOS GmbHarchived copyDMLS Ti-6Al-4V ELI Titanium · Young's modulus (stiffness): same maker and process, sibling grade: EOS Titanium Ti64 (Grade 5) on EOS M 290, as built, XY and Z, typical
- 4TIMETAL 6-4 PropertiesTIMETarchived copyDMLS Ti-6Al-4V ELI Titanium · Poisson's ratio: wrought TIMETAL 6-4 (TIMET measurement, mean of 10); composition-level, not DMLS-measuredDMLS Ti-6Al-4V ELI Titanium · Melting point: melting range, wrought TIMETAL 6-4 (composition-level)
- 5Zinc Die Casting Properties Guide (2012)Eastern AlloysZinc Zamak 3 · Poisson's ratio: typical, Zamak 3 hot-chamber die cast
- 6TIMETAL 6-4 Data SheetTIMETarchived copyDMLS Ti-6Al-4V ELI Titanium · Thermal conductivity: base material: wrought Ti-6Al-4V / 6-4 ELI (TIMET datasheet), 20 °CDMLS Ti-6Al-4V ELI Titanium · Specific heat: base material: wrought Ti-6Al-4V / 6-4 ELI (TIMET datasheet), 20 °C
- 7EOS Titanium Ti64 Grade 23 Material Data SheetEOS GmbHarchived copyDMLS Ti-6Al-4V ELI Titanium · Thermal expansion: mean 25-100 °C, ASTM E228; EOS Ti64 Grade 23 (=ELI) on EOS M 290 40 µm; condition not stated (sheet's mechanical data are heat treated)
Each number points to the document that states it, with the exact basis. Values without a number are computed from the sourced ones. "Not sourced" means no citable source states it (or only a specification minimum); figures computed from it are left out too.
DMLS Ti-6Al-4V ELI Titanium is 3D printed: its properties depend on build direction and print settings; these are typical values.
Questions
Mechanical
Is DMLS Ti-6Al-4V ELI Titanium stronger than Zinc Zamak 3?
DMLS Ti-6Al-4V ELI Titanium is stronger: its yield strength is 1,100 MPa against 221 MPa for Zinc Zamak 3 (4.98x).
Which is lighter, DMLS Ti-6Al-4V ELI Titanium or Zinc Zamak 3?
DMLS Ti-6Al-4V ELI Titanium is lighter: 4,400 kg/m³ against 6,600 kg/m³ for Zinc Zamak 3.
Which is stiffer, DMLS Ti-6Al-4V ELI Titanium or Zinc Zamak 3?
DMLS Ti-6Al-4V ELI Titanium is stiffer: Young's modulus 110 GPa against 85.5 GPa for Zinc Zamak 3, so the same part in DMLS Ti-6Al-4V ELI Titanium deflects less under the same load.
Which is lighter for the same job, DMLS Ti-6Al-4V ELI Titanium or Zinc Zamak 3?
For the same stiffness or strength: DMLS Ti-6Al-4V ELI Titanium is lighter for a stiff rod or tie (tension), stiff beam (bending), stiff panel or plate, strong rod or tie, strong beam, strong panel or plate.
| Part that must be | DMLS Ti-6Al-4V ELI Titanium | Zinc Zamak 3 |
|---|---|---|
| Stiff rod or tie (tension) | lighter | 1.93x heavier |
| Stiff beam (bending) | lighter | 1.7x heavier |
| Stiff panel or plate | lighter | 1.63x heavier |
| Strong rod or tie | lighter | 7.47x heavier |
| Strong beam | lighter | 4.37x heavier |
| Strong panel or plate | lighter | 3.35x heavier |
For the same stiffness or strength, mass scales with density over stiffness (or strength) raised to a power set by how the part is loaded: 1 for a rod in tension, 1/2 for a beam in bending, 1/3 for a panel (the standard material-selection indices).
Which is more ductile, DMLS Ti-6Al-4V ELI Titanium or Zinc Zamak 3?
Zinc Zamak 3 stretches further before it breaks: 10% elongation at break against 8.7% for DMLS Ti-6Al-4V ELI Titanium.
Thermal
Which conducts heat better, DMLS Ti-6Al-4V ELI Titanium or Zinc Zamak 3?
Zinc Zamak 3 conducts heat better: 113 W/m·K against 6.6 W/m·K for DMLS Ti-6Al-4V ELI Titanium.
Which expands less with temperature?
DMLS Ti-6Al-4V ELI Titanium expands less: 9 µm/m·K against 27.4 µm/m·K for Zinc Zamak 3.
Related comparisons
- DMLS Ti-6Al-4V ELI Titanium vs. Titanium
- DMLS Ti-6Al-4V ELI Titanium vs. Titanium Ti-6Al-4V
- DMLS Ti-6Al-4V ELI Titanium vs. Stainless Steel 17-4PH
- DMLS Ti-6Al-4V ELI Titanium vs. Steel AISI 4340
- Zinc Zamak 3 vs. Brass C360
- Zinc Zamak 3 vs. Brass C260
- Zinc Zamak 3 vs. Stainless Steel 304
- Zinc Zamak 3 vs. Stainless Steel 316