Thermal conductivity against densityHigher and further left: spreads more heat for its weightThermal expansion against thermal conductivityLower and further right: warps less when heated
Try it on a partA bracket to run stress or thermal on, free in your browser
MIL-HDBK-5J, Metallic Materials and Elements for Aerospace Vehicle Structures (2003)U.S. Department of DefenseMagnesium AZ31B-H24 · Young's modulus (stiffness): typical (handbook physical constant)Magnesium AZ31B-H24 · Density: nominalMagnesium AZ31B-H24 · Poisson's ratio: typical (handbook physical constant)Magnesium AZ31B-H24 · Max service temperature: stated application limit
4
Luran S 777K (ASA) Product Data SheetINEOS StyrolutionFDM ASA · Thermal conductivity: base material: INEOS Styrolution Luran S 777K injection-molding ASA, typicalFDM ASA · Thermal expansion: base material: INEOS Styrolution Luran S 777K injection-molding ASA, range
Each number points to the document that states it, with the exact basis. Values without a number are computed from the sourced ones. "Not sourced" means no citable source states it (or only a specification minimum); figures computed from it are left out too.
FDM ASA is 3D printed: its properties depend on build direction and print settings; these are typical values.
Questions
Mechanical
Is FDM ASA stronger than Magnesium AZ31B-H24?
Magnesium AZ31B-H24 is stronger: its yield strength is 220 MPa against tensile strength 37 MPa for FDM ASA (5.95x).
Which is lighter, FDM ASA or Magnesium AZ31B-H24?
FDM ASA is lighter: 1,050 kg/m³ against 1,769 kg/m³ for Magnesium AZ31B-H24.
Which is stiffer, FDM ASA or Magnesium AZ31B-H24?
Magnesium AZ31B-H24 is stiffer: Young's modulus 44.8 GPa against 2.45 GPa for FDM ASA, so the same part in Magnesium AZ31B-H24 deflects less under the same load.
Which is lighter for the same job, FDM ASA or Magnesium AZ31B-H24?
For the same stiffness or strength: Magnesium AZ31B-H24 is lighter for a stiff rod or tie (tension), stiff beam (bending), stiff panel or plate, strong rod or tie, strong beam, strong panel or plate.
Part that must be
FDM ASA
Magnesium AZ31B-H24
Stiff rod or tie (tension)
10.9x heavier
lighter
Stiff beam (bending)
2.54x heavier
lighter
Stiff panel or plate
1.56x heavier
lighter
Strong rod or tie
3.53x heavier
lighter
Strong beam
1.95x heavier
lighter
Strong panel or plate
45% heavier
lighter
For the same stiffness or strength, mass scales with density over stiffness (or strength) raised to a power set by how the part is loaded: 1 for a rod in tension, 1/2 for a beam in bending, 1/3 for a panel (the standard material-selection indices).
Which is more ductile, FDM ASA or Magnesium AZ31B-H24?
Magnesium AZ31B-H24 stretches further before it breaks: 13% elongation at break against 9.2% for FDM ASA.
Thermal
Which conducts heat better, FDM ASA or Magnesium AZ31B-H24?
Magnesium AZ31B-H24 conducts heat better: 76.9 W/m·K against 0.17 W/m·K for FDM ASA.
Which expands less with temperature?
Magnesium AZ31B-H24 expands less: 26.8 µm/m·K against 95 µm/m·K for FDM ASA.