Thermal conductivity against densityHigher and further left: spreads more heat for its weightThermal expansion against thermal conductivityLower and further right: warps less when heated
Try it on a partA bracket to run stress or thermal on, free in your browser
Sources4 documents: Cleveland-Cliffs, Bambu Lab, Steel Construction Institute, INEOS Styrolution
FDM ASA
Bambu Lab ASA, TDS V3.0, printed specimens X-Y; nozzle 260 °C, bed 80 °C, 200 mm/s, 100% infill; annealed and dried 80 °C for 12 h before testing.
Stainless Steel 304
Type 304, annealed flat-rolled (Cleveland-Cliffs 304/304L Product Data Bulletin, May 2021); Poisson's ratio from the Nickel Institute/SCI structural stainless design manual
1
304/304L Stainless Steel Product Data Bulletin (2021)Cleveland-CliffsStainless Steel 304 · Yield strength: typical, annealed, 70 °F (21 °C)Stainless Steel 304 · Ultimate tensile strength: typical, annealed, 70 °F (21 °C)Stainless Steel 304 · Elongation at break: typical, annealed, in 2 in. (50.8 mm)Stainless Steel 304 · Young's modulus (stiffness): typical, in tensionStainless Steel 304 · Density: typicalStainless Steel 304 · Thermal conductivity: at 100 °CStainless Steel 304 · Thermal expansion: mean, 0–100 °CStainless Steel 304 · Specific heat: mean, 0–100 °CStainless Steel 304 · Melting point: melting rangeStainless Steel 304 · Max service temperature: continuous, oxidation (scaling) limit in air
Design Manual for Structural Stainless Steel, 4th Edition (P413)Steel Construction Institutearchived copyStainless Steel 304 · Poisson's ratio: design value (structural stainless steels)
4
Luran S 777K (ASA) Product Data SheetINEOS StyrolutionFDM ASA · Thermal conductivity: base material: INEOS Styrolution Luran S 777K injection-molding ASA, typicalFDM ASA · Thermal expansion: base material: INEOS Styrolution Luran S 777K injection-molding ASA, range
Each number points to the document that states it, with the exact basis. Values without a number are computed from the sourced ones. "Not sourced" means no citable source states it (or only a specification minimum); figures computed from it are left out too.
FDM ASA is 3D printed: its properties depend on build direction and print settings; these are typical values.
Questions
Mechanical
Is FDM ASA stronger than Stainless Steel 304?
Stainless Steel 304 is stronger: its yield strength is 241 MPa against tensile strength 37 MPa for FDM ASA (6.51x).
Which is lighter, FDM ASA or Stainless Steel 304?
FDM ASA is lighter: 1,050 kg/m³ against 8,030 kg/m³ for Stainless Steel 304.
Which is stiffer, FDM ASA or Stainless Steel 304?
Stainless Steel 304 is stiffer: Young's modulus 193 GPa against 2.45 GPa for FDM ASA, so the same part in Stainless Steel 304 deflects less under the same load.
Which is lighter for the same job, FDM ASA or Stainless Steel 304?
For the same stiffness or strength: FDM ASA is lighter for a stiff panel or plate, strong rod or tie, strong beam, strong panel or plate; Stainless Steel 304 is lighter for a stiff rod or tie (tension), stiff beam (bending).
Part that must be
FDM ASA
Stainless Steel 304
Stiff rod or tie (tension)
10.3x heavier
lighter
Stiff beam (bending)
16% heavier
lighter
Stiff panel or plate
lighter
1.78x heavier
Strong rod or tie
lighter
17% heavier
Strong beam
lighter
2.19x heavier
Strong panel or plate
lighter
3x heavier
For the same stiffness or strength, mass scales with density over stiffness (or strength) raised to a power set by how the part is loaded: 1 for a rod in tension, 1/2 for a beam in bending, 1/3 for a panel (the standard material-selection indices).
Which is more ductile, FDM ASA or Stainless Steel 304?
Stainless Steel 304 stretches further before it breaks: 55% elongation at break against 9.2% for FDM ASA.
Thermal
Which conducts heat better, FDM ASA or Stainless Steel 304?
Stainless Steel 304 conducts heat better: 16.2 W/m·K against 0.17 W/m·K for FDM ASA.
Which expands less with temperature?
Stainless Steel 304 expands less: 16.9 µm/m·K against 95 µm/m·K for FDM ASA.