Thermal conductivity against densityHigher and further left: spreads more heat for its weightThermal expansion against thermal conductivityLower and further right: warps less when heated
Try it on a partA bracket to run stress or thermal on, free in your browser
Sources4 documents: ATI, Bambu Lab, Steel Construction Institute, INEOS Styrolution
FDM ASA
Bambu Lab ASA, TDS V3.0, printed specimens X-Y; nozzle 260 °C, bed 80 °C, 200 mm/s, 100% infill; annealed and dried 80 °C for 12 h before testing.
Stainless Steel 316
ATI 316 (UNS S31600), annealed 1.0 mm sheet, ATI technical data sheet (2012); Poisson's ratio from the Nickel Institute/SCI structural stainless design manual
1
ATI 316, 316L, 317 and 317L Technical Data Sheet (2012)ATIarchived copyStainless Steel 316 · Yield strength: typical (representative), annealed 1.0 mm sheetStainless Steel 316 · Ultimate tensile strength: typical (representative), annealed 1.0 mm sheetStainless Steel 316 · Elongation at break: typical (representative), annealed, in 2 in. (51 mm)Stainless Steel 316 · Young's modulus (stiffness): typical, in tensionStainless Steel 316 · Density: typicalStainless Steel 316 · Thermal conductivity: 20–100 °CStainless Steel 316 · Thermal expansion: mean, 20–100 °CStainless Steel 316 · Specific heat: at 20 °CStainless Steel 316 · Melting point: melting rangeStainless Steel 316 · Max service temperature: oxidation (scaling) limit in air
Design Manual for Structural Stainless Steel, 4th Edition (P413)Steel Construction Institutearchived copyStainless Steel 316 · Poisson's ratio: design value (structural stainless steels)
4
Luran S 777K (ASA) Product Data SheetINEOS StyrolutionFDM ASA · Thermal conductivity: base material: INEOS Styrolution Luran S 777K injection-molding ASA, typicalFDM ASA · Thermal expansion: base material: INEOS Styrolution Luran S 777K injection-molding ASA, range
Each number points to the document that states it, with the exact basis. Values without a number are computed from the sourced ones. "Not sourced" means no citable source states it (or only a specification minimum); figures computed from it are left out too.
FDM ASA is 3D printed: its properties depend on build direction and print settings; these are typical values.
Questions
Mechanical
Is FDM ASA stronger than Stainless Steel 316?
Stainless Steel 316 is stronger: its yield strength is 265 MPa against tensile strength 37 MPa for FDM ASA (7.16x).
Which is lighter, FDM ASA or Stainless Steel 316?
FDM ASA is lighter: 1,050 kg/m³ against 8,027 kg/m³ for Stainless Steel 316.
Which is stiffer, FDM ASA or Stainless Steel 316?
Stainless Steel 316 is stiffer: Young's modulus 200 GPa against 2.45 GPa for FDM ASA, so the same part in Stainless Steel 316 deflects less under the same load.
Which is lighter for the same job, FDM ASA or Stainless Steel 316?
For the same stiffness or strength: FDM ASA is lighter for a stiff panel or plate, strong rod or tie, strong beam, strong panel or plate; Stainless Steel 316 is lighter for a stiff rod or tie (tension), stiff beam (bending).
Part that must be
FDM ASA
Stainless Steel 316
Stiff rod or tie (tension)
10.7x heavier
lighter
Stiff beam (bending)
18% heavier
lighter
Stiff panel or plate
lighter
1.76x heavier
Strong rod or tie
lighter
7% heavier
Strong beam
lighter
2.06x heavier
Strong panel or plate
lighter
2.86x heavier
For the same stiffness or strength, mass scales with density over stiffness (or strength) raised to a power set by how the part is loaded: 1 for a rod in tension, 1/2 for a beam in bending, 1/3 for a panel (the standard material-selection indices).
Which is more ductile, FDM ASA or Stainless Steel 316?
Stainless Steel 316 stretches further before it breaks: 61% elongation at break against 9.2% for FDM ASA.
Thermal
Which conducts heat better, FDM ASA or Stainless Steel 316?
Stainless Steel 316 conducts heat better: 14.6 W/m·K against 0.17 W/m·K for FDM ASA.
Which expands less with temperature?
Stainless Steel 316 expands less: 16.5 µm/m·K against 95 µm/m·K for FDM ASA.